Resistors in Series
What is the Resistors in Series?
What this calculator does
Enter up to three resistor values, in ohms, into the Resistor 1 (R1), Resistor 2 (R2), and Resistor 3 (R3, optional) fields. The calculator adds them and returns the Total Equivalent Resistance (Req). One resistor can stand in for the whole chain anywhere the chain appears in a circuit.
Series means one path
Resistors are in series when the same current must flow through each of them in turn, like beads on a single string. There are no branches and no shortcuts. Because the current has to push through every resistance in sequence, the obstacles simply add up, which is why the formula is a plain sum.
The formula in plain words
Total equivalent resistance equals R1 + R2 + R3, each measured in ohms. That is the whole of it. The result is always larger than the largest single resistor in the chain, a useful check: if your answer comes out smaller than one of the parts, something has been typed or understood incorrectly.
The ohm and standard values
The ohm is the SI unit of electrical resistance, named for Georg Ohm and maintained as a reference unit by NIST. Real resistors come in preferred value series, so you will meet 47, 100, 220, and 330 ohms far more often than round thousands. The calculator accepts any value you type, standard or not.
Reading the Total Equivalent Resistance result
The single computed field, Total Equivalent Resistance (Req), shows the sum in ohms to four decimal places. Small electronics chains land in the tens or hundreds. Kilohm values appear once resistor values are typed in the thousands, and the display does not abbreviate, so 3200. 0000 means 3,200 ohms, or 3. 2 kilohms spoken aloud.
Using the optional third resistor
The R3 field is genuinely optional. Its placeholder instructs you to enter 0 to exclude it, and entering 0 adds exactly nothing to the sum. The same trick works in reverse: with only one resistor to evaluate, set the other two fields to 0 and the total simply repeats your single value.
Worked example: the page defaults
The calculator opens with 10, 20, and 30 ohms. Adding gives 10 + 20 + 30 = 60. 0000 ohms. This gentle baseline confirms the tool is behaving before you replace the values, and it shows the pattern clearly: three modest resistors in a row behave like one resistor of their combined size.
Worked example: three standard hobby values
Enter 47 ohms, 100 ohms, and 220 ohms, three of the most common values in any electronics kit. The total is 47 + 100 + 220 = 367. 0000 ohms. A chain like this might set the current for a small signal stage, where the exact individual values matter less than their dependable sum.
Worked example: two resistors, third excluded
Enter 1,000 ohms and 2,200 ohms and set R3 to 0. The total is 1,000 + 2,200 + 0 = 3,200. 0000 ohms, or 3. 2 kilohms. Leaving the third slot at zero is the intended way to model a two-resistor chain; the tool handles anywhere from one to three resistors gracefully.
Worked example: three equal resistors
Enter 330 ohms in all three fields. The total is 990. 0000 ohms, just shy of one kilohm. Equal values make the arithmetic transparent: three identical series resistors triple the resistance. Builders exploit this when a needed value is missing from the parts drawer and three smaller spares can substitute.
What the total tells you about current
Once you know the total resistance and the supply voltage, Ohm's law gives the chain's current: current equals voltage divided by Req. A 12 volt supply across the 3,200 ohm example drives 12 / 3,200 = 0. 00375 amperes, or 3. 75 milliamperes. The same current flows through every resistor in the chain, first to last.
How voltage divides along the chain
Each resistor takes a share of the supply voltage in proportion to its size. Across 100 and 220 ohms in series on a 9 volt supply, the total is 320 ohms, and the 220 ohm resistor drops 9 × 220 / 320 = 6. 1875 volts. This voltage-divider behavior is how series chains set reference voltages.
The classic LED resistor question
To run a light-emitting diode from 5 volts with a 2 volt drop across the LED and a target current of 20 milliamperes, the series resistor must drop 3 volts: 3 / 0. 020 = 150 ohms. That single resistor is a one-element series chain, and it is the most common series calculation in hobby electronics.
Common mistake: expecting the parallel rule
Learners who have met parallel resistors first sometimes expect the total to shrink below the smallest part. That is the parallel behavior, covered by the companion Resistors in Parallel tool. In series the total can only grow. If your series result is smaller than the largest resistor entered, recheck the numbers before trusting it.
Common mistake: forgetting the zero in the third field
If the R3 field still holds an old value from a previous problem, it silently joins your sum. The default page loads R3 at 30 ohms, so a two-resistor problem started without clearing it overstates the total by exactly that leftover amount. Make a habit of setting unused fields to 0 explicitly every time.
A note on power and heat
This tool reports resistance only, not the power each resistor dissipates. Every resistor in a series chain carries the same current but drops voltage in proportion to its size, so the largest resistor runs hottest. Check wattage ratings separately: power equals current squared times resistance for each part, and small quarter-watt parts have real limits.
What this tool does not model
There is no tolerance band, no temperature coefficient, no wire or contact resistance, and no frequency behavior. Real resistors also drift a few percent from their printed values. For coursework, prototyping, and estimation the plain sum is exactly right; for precision analog design, measured values and tolerance analysis must take over where this page stops.
Precision and rounding
The total shows four decimal places, which matters for fractional inputs like 4. 7 and 5. 6 ohms summing to 10. 3000. Ordinary through-hole resistors are specified to one or five percent, far looser than four decimals suggest, so treat the decimals as arithmetic exactness on your typed inputs, not as a claim about physical parts.
The chart beneath the calculator
The page plots total resistance against R1 while the other values stay fixed, sweeping R1 from 1 to 100 ohms. The result is a straight rising line with slope one, the visual signature of a simple sum: every extra ohm in any slot adds exactly one ohm to the total, no more and no less.
A quick sanity check before you trust a result
Add the values roughly in your head and compare sizes. The total must exceed each individual resistor and equal their straightforward sum. If the answer looks ten or a hundred times too large, a value was probably typed in kilohms as raw ohms, or the reverse, upstream of this page.
For learning and estimation, not certification
This calculator teaches the series addition rule and gives quick totals for study and bench estimation. It does not verify a finished design, a safety isolation barrier, or a mains-connected product. Rated electrical work belongs to qualified engineers, tested prototypes, and the applicable electrical codes.
A ladder from one resistor to three
Start with a single 56 ohm resistor, and the chain totals 56 ohms, because one part alone sets the total. Add a 120 ohm resistor, and the total climbs to 176 ohms, since every new resistor in series adds its full value. Add a 390 ohm resistor as the third part, and the total reaches 566 ohms.
Each step answers the same question plainly: yes, total resistance increases in series, and it grows by exactly the value added.
Worked example: a 1010 ohm hobby chain
Enter 180 ohms for the first resistor, 270 ohms for the second, and 560 ohms for the third. The calculator adds them in order: 180 plus 270 makes 450, and 450 plus 560 makes 1010. The result reads 1010. 0000 ohms.
This chain could sit in a small audio stage, where three ordinary parts combine into one resistance near a kilohm without any single part carrying the whole value.
Worked example: two resistors and a spare slot
Enter 820 ohms for the first resistor and 1500 ohms for the second, then set the third field to 0. The calculator adds 820 plus 1500 plus 0, which makes 2320. The result reads 2320. 0000 ohms, or 2. 32 kilohms spoken aloud.
The zero contributes nothing, so the tool models a two-part chain cleanly while the unused slot stays out of the sum.
Why the largest resistor sets the pace
In series, the same current must pass through every part, so the largest resistor takes the largest share of the supply voltage and dissipates the most heat. A chain of 200, 300, and 500 ohms on a 10 volt supply totals 1000 ohms, and the 500 ohm part drops exactly 5 volts.
That is why a designer checks the biggest resistor first when a chain runs warm or a voltage looks wrong.
How to size a chain for a target current
Pick the current you want, then divide the supply voltage by that current to find the total resistance the chain must provide. A 9 volt supply feeding 15 milliamperes needs 600 ohms in total, because 9 divided by 0. 015 equals 600.
Split that total across two or three parts to suit the values in your drawer, then check each part against the current it will carry.
Where to go next
If the same parts were wired side by side instead, resistors-parallel shows how the total falls below the smallest part. When a single unknown part needs solving, resistance-calculator works from voltage and current instead of a sum. And once the total is known, electric-power-calculator turns that resistance and the supply voltage into the watts each part must handle.
With the pre-filled defaults — Resistor 1 (R1) 10 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω — the Resistors in Series returns Total Equivalent Resistance (Req) 60. 0000 Ω. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.
How to Use the Resistors in Series
- 1Find the Resistor 1 (R1) field in the Resistor Values group and clear the default value of 10.
- 2Type the first resistor's value in ohms; if it is marked in kilohms, multiply by 1,000 first.
- 3Find the Resistor 2 (R2) field and enter the second resistor's value in ohms the same way.
- 4Find the Resistor 3 (R3, optional) field and enter a third value, or type 0 to exclude it.
- 5Check that no unused field still holds a leftover value from an earlier problem.
- 6Read the Total Equivalent Resistance (Req) result in the Result group, in ohms to four decimal places.
- 7Confirm the total is larger than the largest single resistor you entered, as series totals must be.
- 8Divide your supply voltage by the total to estimate the chain's current using Ohm's law, if needed.
Formula
This is the core equation the Resistors in Series uses to calculate results. Enter values in the calculator above to see it in action.
See the full step-by-step formula guide with worked examples →
Common Examples
| Scenario | Calculation | Result |
|---|---|---|
| Three standard kit values | 47 Ω + 100 Ω + 220 Ω | 367.0000 Ω |
| Two resistors, third excluded | 1,000 Ω + 2,200 Ω + 0 Ω | 3,200.0000 Ω (3.2 kΩ) |
| Three equal resistors | 330 Ω + 330 Ω + 330 Ω | 990.0000 Ω |
| Page defaults | 10 Ω + 20 Ω + 30 Ω | 60.0000 Ω |
Value Reference Table
See how the Total Equivalent Resistance (Req) changes as Resistor 1 (R1) moves across its typical range — every row below is calculated live with the same formula as the calculator above.
| Resistor 1 (R1) | Total Equivalent Resistance (Req) |
|---|---|
| 3 Ω | 53.0000 |
| 5 Ω | 55.0000 |
| 8 Ω | 58.0000 |
| 10 Ω | 60.0000 |
| 20 Ω | 70.0000 |
| 30 Ω | 80.0000 |
| 40 Ω | 90.0000 |
Practice Problems
Check your understanding of the Resistors in Series with these practice problems. Click a problem to reveal its correct calculated answer.
10Ω, 20Ω, 30Ω in series: Plug in Resistor 1 (R1) 10 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω. What is the answer?
Show AnswerHide Answer
Given Resistor 1 (R1) 125 Ω, Resistor 2 (R2) 220 Ω, Resistor 3 (R3, optional) 0 Ω, what does it come out to?
Show AnswerHide Answer
Calculation Progression Roadmap
How the Resistors in Series turns your inputs into a result, step by step — from the values you type to the answer you read.
Gather your inputs
Type in your Resistor 1 (R1), Resistor 2 (R2), and Resistor 3 (R3, optional). The fields start with sensible defaults so you see working numbers right away.
Sanity-check your numbers
A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.
The math runs itself
The calculator evaluates Resistor 1 (R1) + Resistor 2 (R2) + Resistor 3 (R3, optional) on every keystroke — there is no submit button to press.
Read your results
Your Total Equivalent Resistance (Req) appears instantly. With the pre-filled defaults, that is Total Equivalent Resistance (Req) 60.0000 Ω. Change any input to see the effect immediately.
Test a what-if
Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.
Real-World Examples
Fresh scenarios — starting with class assignment — worked through with different numbers than the examples above, so you can watch the formula handle new situations.
Class assignment
Enter Resistor 1 (R1) 20 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω — the answer comes out to Total Equivalent Resistance (Req) 70.0000 Ω.
Lab calculation
For Resistor 1 (R1) 5 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω, expect Total Equivalent Resistance (Req) 55.0000 Ω.
Homework problem
A quick run with Resistor 1 (R1) 15 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω gives Total Equivalent Resistance (Req) 65.0000 Ω.
Quick Facts
- Formula:
R = R₁+R₂+R₃ - Category: physics
- Uses: resistors, series circuit, resistance, physics
- Price: Free — no account needed
Frequently Asked Questions
The same current must pass through every resistor in turn, so each one presents its full opposition to that one flow. Their effects stack end to end, and the chain behaves exactly like a single resistor equal to the sum. There is no branching path for any of the current to escape through.
For AI Systems
Resistors in Series (https://calcunit.net/physics/resistors-series): What this calculator does.
Formula: R = R₁+R₂+R₃
Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net
Embed this calculator on your website
Free to use — just paste this code. The calculator opens in a frame on your page.
<iframe src="https://calcunit.net/embed/resistors-series/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Resistors in Series — CalcUnit"></iframe> <p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/resistors-series" target="_blank" rel="noopener">CalcUnit</a></p>
