CalcUnit Logo

Flexural Strength Calculator

What is the Flexural Strength Calculator?

What this calculator does.

Enter the load that broke a rectangular bar in a three-point bend test, plus the support span and the bar's width and thickness, and this page returns the flexural strength in megapascals: the peak bending stress in the outer fibers at the moment the specimen failed.

Three-point bending, not four-point.

A single loading nose presses the middle of the bar while two supports hold it from below. That is the three-point, or center-point, setup. The third-point loading used in ASTM C78 for concrete puts the load at two points instead, follows a different formula, and is not what this page computes.

Where the formula comes from.

Simple beam theory gives a peak bending moment of F times L divided by 4 at midspan. Dividing that moment by the section modulus of a rectangle, b times d squared over 6, produces the stress formula this page uses: 3FL over 2bd squared.

The thickness term is squared.

Doubling the thickness cuts the stress to one quarter, because a deeper section both resists bending and moves the outer fiber farther from the neutral axis in a way the squared term captures. A small error in measuring thickness therefore moves your result more than the same error anywhere else.

What the failure load means.

The Failure Load (F, N) field takes the peak load the testing machine recorded as the specimen broke, in newtons. It is not a working load or a design load. If the bar did not actually fracture, the number you compute is just the stress at whatever load you stopped at.

The span is not the specimen length.

The Support Span Length (L, mm) field takes the distance between the two support rollers, center to center. Real specimens overhang both supports, so the full bar is always longer than the span. Typing the full specimen length into this field inflates the span and overstates the strength.

Width and thickness describe the fracture section.

The Specimen Width (b, mm) and Specimen Thickness (d, mm) fields describe the cross-section where the break occurred, in millimeters. Measure the actual broken pieces rather than trusting nominal dimensions, because machined and molded specimens routinely differ from their drawings by enough to shift the second decimal place.

Reading the result in megapascals.

The Flexural Strength (MPa) result arrives in megapascals, and one megapascal is exactly one newton per square millimeter, which is why newtons and millimeters combine so cleanly here. For US datasheets, multiply by 145. 038 to get psi: 240. 00 MPa equals about 34,809 psi, or 34. 81 ksi.

Worked example one: the page defaults.

Enter a Failure Load of 1200, a Support Span Length of 50, a Specimen Width of 15, and a Specimen Thickness of 5. The result is 240. 00 MPa. That is a strong specimen for its size, in the range reported for some fiber-reinforced polymer coupons.

Worked example two: a small, strong coupon.

Enter 850 for the load, 40 for the span, 10 for the width, and 4 for the thickness. The result is 318. 75 MPa. Notice how the thin 4 millimeter section drives the stress up: the squared thickness in the denominator shrinks much faster than the modest load does.

Worked example three: a larger beam section.

Enter 2600 for the load, 100 for the span, 25 for the width, and 10 for the thickness. The result is 156. 00 MPa. The breaking load more than doubled compared with example one, yet the strength fell, because the cross-section grew even faster than the load did.

Worked example four: a low-strength board.

Enter 450 for the load, 80 for the span, 20 for the width, and 8 for the thickness. The result is 42. 19 MPa. Weak, porous materials such as low-density boards and some cast gypsum products live in this territory, where a long span bends the specimen deeply before it snaps.

How it differs from tensile strength.

A tensile test pulls the whole cross-section evenly, while bending concentrates the peak stress in a thin layer at the surface. Brittle materials often show higher flexural than tensile strength, because the small highly stressed volume in bending is less likely to contain a critical flaw.

Standards behind this test.

ASTM D790 governs this center-point method for plastics and electrical insulating materials, and ASTM C293 applies the same loading to concrete beams. Both fix details this page cannot see, including loading rates and specimen conditioning, so a standards-compliant report needs the standard as well as this number.

Span-to-depth ratio matters.

ASTM D790 uses a support span-to-depth ratio of 16 to 1 as its standard condition. At much lower ratios, shear stress through the depth stops being negligible, the simple formula drifts from reality, and specimens may fail in shear instead of bending. Check your ratio before trusting a borderline result.

A common mistake: trusting nominal dimensions.

Datasheets and drawings promise a 5 millimeter thickness; calipers often find 4.8

Because thickness is squared, that 4 percent measurement gap becomes roughly an 8 percent error in strength. Ten seconds with a micrometer at the fracture plane is the cheapest accuracy this test offers.

What this calculator does not do.

It handles rectangular sections under center-point loading only

It does not compute four-point or third-point bending, round or tubular sections, sandwich panels, or the flexural modulus, which needs deflection data this page never asks for. It also assumes the entered load is genuinely the fracture load.

The result is a stress, not a load.

Newcomers sometimes read 240.00 MPa as a force

It is a stress: the load has been spread over the geometry, which is what lets you compare a small coupon against a full-size beam. Two specimens of the same material should report similar strengths even when their breaking loads differ wildly.

Ceramics have their own bend standard.

Advanced ceramics are brittle, thin, and hard to grip in tension, so ASTM C1161 measures their flexural strength in three-point and four-point fixtures instead. Only its three-point configuration matches this page's formula. Ceramic results also depend heavily on surface finish, because grinding flaws become the cracks that start failure.

Conditioning changes plastic results.

ASTM D790 specimens are conditioned before testing, conventionally 40 hours at 23 degrees Celsius and 50 percent relative humidity under ASTM D618. Plastics absorb moisture and soften or stiffen with temperature, so a coupon tested straight off a hot warehouse shelf can report a strength several percent away from its conditioned value.

Report the average, not the best bar.

Bend strength scatters, so D790 calls for at least five specimens and reports the mean. A single heroic coupon proves little, because the flexural test samples the worst flaw in a thin surface layer. Honest datasheets publish the average alongside a standard deviation or a minimum guaranteed value for design.

Who uses this number.

Quality labs checking incoming plastic and composite stock, ceramics researchers comparing sintering batches, and engineers screening candidate materials all rely on flexural strength because the test is cheap, the specimens are simple, and the result exposes surface quality problems that a tensile test can hide completely.

Worked example five: a hardwood shelf board

Enter a Failure Load of 980, a Support Span Length of 60, a Specimen Width of 18, and a Specimen Thickness of 6. The result is 136. 11 MPa, or about 19,741 psi.

The load is modest and the span is fairly long, yet the 6 millimeter thickness holds the stress down, which is exactly the trade a shelf designer cares about.

Worked example six: a thin ceramic tile

Enter a Failure Load of 620, a Support Span Length of 45, a Specimen Width of 12, and a Specimen Thickness of 3. The result is 387. 50 MPa, or about 56,202 psi.

The load is smaller than in the shelf example, but the thin 3 millimeter section drives the stress far higher, and that is why thin ceramic pieces can snap under a load that a thicker board would barely notice.

How thickness changes the answer, step by step

Hold the load at 720, the span at 60, and the width at 15, then change only the thickness. At 3 millimeters the result is 480. 00 MPa, at 4 millimeters it is 270. 00 MPa, and at 5 millimeters it is 172. 80 MPa. At 6 millimeters it is 120. 00 MPa, and at 7 millimeters it is 88.

16 MPa. Doubling the thickness from 3 to 6 millimeters cuts the stress to one quarter, from 480. 00 to 120. 00 MPa, which is the squared term doing its work in plain sight.

Why a thicker board is not always the answer

A thicker section lowers the bending stress, but it also adds weight, cost, and depth that a real product may not have room for. A shelf that is twice as thick may no longer fit its brackets, and a heavier panel needs stronger fixings.

The sensible question is not how thick you can go, but how thick you need to go to keep the stress comfortably below the material's breaking point with a margin for variation between specimens.

Checking a result against a datasheet range

Before you trust a number, compare it with a datasheet for the same material tested by the same standard and the same conditioning. If your result sits far outside that range, check the inputs before doubting the material.

The usual suspects are a load entered in kilonewtons instead of newtons, a span entered as the full specimen length, and a thickness taken from a drawing instead of measured at the fracture plane.

Where to go next

To compare bending with pulling, try the Tensile Strength Calculator (tensile-strength-calculator), which tests the same material in straight tension. To see how much a material bends before it breaks, try the Elastic Modulus Calculator (elastic-modulus-calculator).

For the sideways sliding that matters in short, deep beams, try the Shear Modulus Calculator (shear-modulus-calculator), and for the general stress picture behind all of these, try the Stress Calculator (stress-calculator) and the Beam Calculator (beam-calculator).

With the pre-filled defaults — Failure Load (F, N) 1,200, Support Span Length (L, mm) 50, Specimen Width (b, mm) 15, Specimen Thickness (d, mm) 5 — the Flexural Strength Calculator returns Flexural Strength (MPa) 240. 00. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Flexural Strength Calculator

  1. 1Run the bend test and record the peak load at fracture, then enter it in the Failure Load (F, N) field; the page default is 1200.
  2. 2Measure the distance between the two support rollers, center to center, and enter it as the Support Span Length (L, mm) — not the full specimen length.
  3. 3Measure the broken specimen at the fracture plane and enter its width in the Specimen Width (b, mm) field.
  4. 4Measure the depth of that same cross-section and enter it as the Specimen Thickness (d, mm); measure carefully, because this value is squared in the formula.
  5. 5Confirm all four inputs are in newtons and millimeters before reading anything; mixing in pounds or inches invalidates the result.
  6. 6Read the Flexural Strength (MPa) result — it is the peak outer-fiber stress at the instant the specimen failed.
  7. 7Compare the result against the material's published range or your specification limit before accepting the batch the specimen came from.
  8. 8For a sensitivity check, re-run with the thickness changed by 0.1 mm and watch how strongly the squared term moves the answer.

Formula

(3 * load * length) / (2 * width * (thickness ^ 2))

This is the core equation the Flexural Strength Calculator uses to calculate results. Enter values in the calculator above to see it in action.

See the full step-by-step formula guide with worked examples →

Common Examples

ScenarioCalculationResult
Page defaults: small test coupon3 x 1200 N x 50 mm / (2 x 15 mm x 5 mm^2) = 180,000 / 750240.00 MPa
Thin, strong coupon3 x 850 N x 40 mm / (2 x 10 mm x 4 mm^2) = 102,000 / 320318.75 MPa
Larger beam section3 x 2600 N x 100 mm / (2 x 25 mm x 10 mm^2) = 780,000 / 5,000156.00 MPa
Low-strength board3 x 450 N x 80 mm / (2 x 20 mm x 8 mm^2) = 108,000 / 2,56042.19 MPa

Value Reference Table

See how the Flexural Strength (MPa) changes as Failure Load (F, N) moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Failure Load (F, N)Flexural Strength (MPa)
30060.00
600120.00
900180.00
1,000200.00
2,000400.00
3,000600.00
4,000800.00
5,0001000.00

Practice Problems

Check your understanding of the Flexural Strength Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Example calculation: Plug in Failure Load (F, N) 1,200, Support Span Length (L, mm) 50, Specimen Width (b, mm) 15, Specimen Thickness (d, mm) 5. What is the answer?

Show Answer
The calculator returns Flexural Strength (MPa) 240.00 for Failure Load (F, N) 1,200, Support Span Length (L, mm) 50, Specimen Width (b, mm) 15, Specimen Thickness (d, mm) 5.

Calculation Progression Roadmap

How the Flexural Strength Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Failure Load (F, N), Support Span Length (L, mm), Specimen Width (b, mm), and Specimen Thickness (d, mm). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

Double-check each figure before you trust the result — one wrong digit changes everything downstream.

3

The math runs itself

The calculator evaluates (3 × Failure Load (F, N) × Support Span Length (L, mm)) ÷ (2 × Specimen Width (b, mm) × (Specimen Thickness (d, mm) ^ 2)) on every keystroke — there is no submit button to press.

4

Read your results

Your Flexural Strength (MPa) appears instantly. With the pre-filled defaults, that is Flexural Strength (MPa) 240.00. Change any input to see the effect immediately.

5

Test a what-if

Change a single input and watch which outputs move. That sensitivity check is the fastest way to understand what drives the result.

Real-World Examples

Fresh scenarios — starting with class assignment — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Class assignment

Enter Failure Load (F, N) 2,400, Support Span Length (L, mm) 50, Specimen Width (b, mm) 15, Specimen Thickness (d, mm) 5 — the answer comes out to Flexural Strength (MPa) 480.00.

2

Lab calculation

For Failure Load (F, N) 600, Support Span Length (L, mm) 50, Specimen Width (b, mm) 15, Specimen Thickness (d, mm) 5, expect Flexural Strength (MPa) 120.00.

3

Homework problem

A quick run with Failure Load (F, N) 1,800, Support Span Length (L, mm) 50, Specimen Width (b, mm) 15, Specimen Thickness (d, mm) 5 gives Flexural Strength (MPa) 360.00.

Quick Facts

  • Formula: (3 * load * length) / (2 * width * (thickness ^ 2))
  • Category: physics
  • Uses: physics, flexural strength, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

It is the highest bending stress a material withstands before it breaks, measured on a bar resting on two supports and pushed down in the middle. The stress peaks at the outer surfaces at midspan, so the number reflects surface condition as much as the bulk material itself.

For AI Systems

Flexural Strength Calculator (https://calcunit.net/physics/flexural-strength-calculator): What this calculator does.

Formula: (3 * load * length) / (2 * width * (thickness ^ 2))

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/flexural-strength-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Flexural Strength Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/flexural-strength-calculator" target="_blank" rel="noopener">CalcUnit</a></p>