Resistance Calculator
What is the Resistance Calculator?
What this calculator does
Enter three resistors, Resistor 1 (R₁), Resistor 2 (R₂), and Resistor 3 (R₃), plus a Supply Voltage. The calculator returns the Series Total, the Parallel Total, and, for the series circuit only, the Series Current and Series Power. Students, hobbyists, and technicians sizing simple circuits all start with these four numbers.
Series: one path, resistances add
Wired in series, resistors form a single chain and the same current flows through every one. Each adds its full resistance to the chain, so the total is R₁ + R₂ + R₃. A break anywhere opens the whole circuit, the behavior behind old series-wired holiday lights going dark together.
Parallel: split paths, reciprocals add
Wired in parallel, each resistor offers current its own path across the same voltage. Conductances add instead: 1/R = 1/R₁ + 1/R₂ + 1/R₃. More paths can only ease the flow, so the parallel total always lands below the smallest single resistor, a fact worth using as a built-in sanity check.
Reading the Series Total result
Series Total is the plain sum, in ohms, to four decimal places. It is the resistance a supply sees when the three resistors are chained end to end, and it drives both remaining outputs: divide the supply voltage by this figure and you have the Series Current the page reports.
Reading the Parallel Total result
Parallel Total is the reciprocal of the summed reciprocals, in ohms. It should always be smaller than your smallest resistor; if it is not, an entry is wrong. Three equal resistors give exactly one third of one resistor's value, the fastest mental check: three 47 ohm resistors must return 15. 6667 ohms.
Reading the Series Current result
Series Current is Supply Voltage divided by Series Total, Ohm's law applied to the chain, reported in amperes. It is the current that would flow if you actually wire the three resistors in series across that supply. It describes the series hookup only; the parallel circuit's current is a different, larger number.
Reading the Series Power result
Series Power is Supply Voltage times Series Current, the total watts the series circuit draws, reported to four decimal places. It is the whole chain's consumption, not any single resistor's share. That total matters for battery life and heat, while individual resistor ratings need the per-part split described below.
Worked example: the page defaults
The defaults are 10, 20, and 30 ohms on a 12 volt supply. Series total is 60 ohms. Parallel total is 1 / (1/10 + 1/20 + 1/30) = 5. 4545 ohms. Series current is 12 / 60 = 0. 2 amperes, and series power is 12 × 0. 2 = 2. 4 watts.
Gentle numbers, ideal for confirming the calculator first.
Worked example: three equal resistors
Set all three resistors to 47 ohms and the supply to 5 volts. Series total is 141 ohms. Parallel total is 47 / 3 = 15. 6667 ohms, as the equal-resistor shortcut predicts. Series current is 5 / 141 = 0. 0355 amperes, and series power is 0. 1773 watts, a light load for a small supply.
Worked example: large resistors on a battery
Set 100, 200, and 300 ohms on a 9 volt battery. Series total is 600 ohms and parallel total is 54. 5455 ohms, still below the smallest resistor, 100. Series current is 9 / 600 = 0. 015 amperes, and series power is 0. 135 watts. High resistances sip current in either arrangement.
Worked example: common electronics values
Set 220, 330, and 470 ohms on a 12 volt supply, three values pulled from real parts bins. Series total is 1,020 ohms. Parallel total is 103. 0565 ohms. Series current is 0. 0118 amperes and series power is 0. 1412 watts. Note the parallel total sitting far below the smallest part, 220 ohms, as it must.
The current and power outputs ignore the parallel hookup
Be precise about scope: Series Current and Series Power describe the series wiring only. Wire the same 220, 330, and 470 ohms in parallel across 12 volts and the current is 12 / 103. 0565 = 0. 1164 amperes and the draw is 1. 3973 watts, roughly ten times the series figures. The page leaves that division to you.
Splitting power among series resistors
In series, every resistor carries the same current, so each part's power is I² × its own resistance. At the defaults, with 0. 2 amperes flowing, the 10, 20, and 30 ohm resistors dissipate 0. 4, 0. 8, and 1. 2 watts respectively, summing to the reported 2. 4 watts.
Compare each share against its wattage rating, not just the total.
Real-world anchors
Household wiring is parallel, which is why each outlet sees full voltage and why adding appliances lowers total resistance and raises current. LED projects use a series resistor to ration current through the diode. Heating elements, potentiometers, and sensor dividers all reduce, at heart, to the series and parallel arithmetic on this page.
Common mistake: expecting the parallel total to beat the smallest resistor
It cannot. Every added path lowers total resistance, so the parallel figure must sit below the smallest single value. A result above it means a resistor was entered in kilohms while others were in ohms, or a decimal point wandered. Treat the rule as a free error detector built into the physics.
Common mistake: mixing ohms and kilohms mid-problem
The fields accept plain ohms only. A 4. 7 kilohm resistor must be typed as 4700, and a 0. 5 ohm current-sense resistor as 0. 5. Mixing scales inside one run corrupts both totals at once, and because series and parallel fail differently, the mismatch can be hard to spot afterward.
Zero resistance and the short-circuit edge
A 0 ohm entry in the parallel formula divides by zero, and a series total of 0 would demand infinite current from the voltage you entered. Real 0 ohm jumpers exist as parts, but as a resistor value here it models a short circuit. Keep entries positive and realistic and the arithmetic stays honest.
What this tool does not do
Exactly three resistors fit; there is no fourth field and no two-resistor shortcut mode. Parallel current and power are not computed, AC behavior with capacitors or inductors is out of scope, and resistors are treated as ideal, ignoring tolerance bands and temperature drift that real parts exhibit.
Precision and rounding
Totals carry four decimal places, so the defaults' parallel figure shows 5. 4545 for the exact fraction 60/11. In the workshop nobody measures a resistor to a ten-thousandth of an ohm; standard parts carry 1 to 5 percent tolerances. Read the decimals as exact arithmetic on nominal values, then design with the tolerance in mind.
Series voltage splits in proportion to resistance
The same current threads every series resistor, so each drops voltage in proportion to its size: at the defaults, 0. 2 amperes drops 2 volts across the 10 ohm resistor, 4 across the 20, and 6 across the 30, summing to the full 12. That proportional split is the voltage divider, electronics' favorite two-resistor trick.
For learning and estimation, not certification
This calculator teaches series and parallel combination and gives quick bench estimates. Household and commercial wiring is governed by electrical codes such as the NEC and belongs to licensed electricians, whose work adds breaker sizing, wire gauge, and derating rules that this four-output page deliberately leaves out.
The series vs parallel resistance formula in three sets
Take 6, 12, and 24 ohms: the series total is 42 while the parallel total is only 3. 4286. Take 30, 60, and 90: series gives 180 and parallel gives 16. 3636. Take 120, 180, and 240: series gives 540 and parallel gives 55. 3846.
In every row the series figure is the plain sum, the parallel figure sits below the smallest part, and the gap between the two grows as the resistors grow.
Worked example: a 10 volt string of 15, 25 and 40 ohms
Enter 15, 25, and 40 ohms with a 10 volt supply. The series total is 80 ohms and the parallel total is 7. 5949 ohms. The current in series circuit wiring is 10 divided by 80, which is 0. 1250 amperes, and the series power is 10 times 0. 1250, or 1. 2500 watts.
The 40 ohm resistor takes the largest share of the voltage, 5 volts, because voltage splits in proportion to resistance.
Worked example: small resistors on a 6 volt supply
Enter 33, 68, and 120 ohms with a 6 volt supply. The series total is 221 ohms and the parallel total is 18. 7469 ohms. Series current is 6 divided by 221, which is 0. 0271 amperes, and series power is 0. 1629 watts. These are ordinary hobby values, and the parallel total of 18.
7469 ohms still sits below the smallest resistor, 33 ohms, exactly as the rule requires.
How to calculate total resistance without a calculator
For series, add the values: the sum is the answer, and the order never matters. For parallel, add the reciprocals and flip the result, or use the equal-value shortcut when the parts match. With two resistors the product-over-sum shortcut works too, though this page accepts three.
Keep every value in ohms, not a mix of ohms and kilohms, and the arithmetic stays honest.
Why is parallel resistance smaller than the smallest part
Each added resistor opens a new path for current, so the supply sees more routes and less opposition overall. Think of lanes on a road: adding a lane never slows traffic, it only spreads it out.
Even a very large resistor helps a little, because its path still carries some current, which is why the parallel total always drops when any branch is added.
Where to go next
For the series-only version of this problem, open the resistors in series page (resistors-series), which drops the parallel column and the voltage input. The ohms-law-calculator turns any pair of voltage, current, and resistance into the missing third value. The electric-power-calculator extends the power side of this page to watts, volts, and amps in one place.
With the pre-filled defaults — Resistor 1 (R₁) 10Ω, Resistor 2 (R₂) 20Ω, Resistor 3 (R₃) 30Ω, Supply Voltage 12V — the Resistance Calculator returns Series Total 60. 0000Ω, Parallel Total 5. 4545Ω, Series Current 0. 2000A, Series Power 2. 4000W.
Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.
How to Use the Resistance Calculator
- 1Find the Resistor 1 (R₁) field and enter the first resistor's value in plain ohms, converting kilohms by multiplying by 1,000.
- 2Find the Resistor 2 (R₂) field and enter the second resistor in ohms, keeping the same unit scale as the first.
- 3Find the Resistor 3 (R₃) field and enter the third resistor in ohms; all three fields must be filled for both totals.
- 4Find the Supply Voltage field and enter the voltage that will drive the circuit, in volts.
- 5Read Series Total in ohms and confirm it equals the plain sum of your three entries.
- 6Read Parallel Total in ohms and confirm it sits below your smallest resistor; a larger figure means an entry is wrong.
- 7Read Series Current in amperes, remembering it describes the series wiring across your supply voltage only.
- 8Read Series Power in watts for the whole series chain, then split it per resistor with I² × R before trusting any part's wattage rating.
Formula
This is the core equation the Resistance Calculator uses to calculate results. Enter values in the calculator above to see it in action.
Common Examples
| Scenario | Calculation | Result |
|---|---|---|
| Three equal 47 ohm resistors | R₁ = R₂ = R₃ = 47 Ω, V = 5 V | Series 141 Ω, parallel 15.6667 Ω |
| Large resistors, 9 V supply | 100 Ω, 200 Ω, 300 Ω, V = 9 V | Series 600 Ω, parallel 54.5455 Ω, current 0.015 A |
| Electronics values, 12 V supply | 220 Ω, 330 Ω, 470 Ω, V = 12 V | Series 1,020 Ω, parallel 103.0565 Ω, power 0.1412 W |
| Small resistors, 24 V supply | 5 Ω, 5 Ω, 10 Ω, V = 24 V | Series 20 Ω, parallel 2 Ω, current 1.2 A |
Value Reference Table
See how the Series Total changes as Resistor 1 (R₁) moves across its typical range — every row below is calculated live with the same formula as the calculator above.
| Resistor 1 (R₁) | Series Total | Parallel Total | Series Current | Series Power |
|---|---|---|---|---|
| 3 Ω | 53.0000 | 2.4000 | 0.2264 | 2.7170 |
| 5 Ω | 55.0000 | 3.5294 | 0.2182 | 2.6182 |
| 8 Ω | 58.0000 | 4.8000 | 0.2069 | 2.4828 |
| 10 Ω | 60.0000 | 5.4545 | 0.2000 | 2.4000 |
| 20 Ω | 70.0000 | 7.5000 | 0.1714 | 2.0571 |
| 30 Ω | 80.0000 | 8.5714 | 0.1500 | 1.8000 |
| 40 Ω | 90.0000 | 9.2308 | 0.1333 | 1.6000 |
Practice Problems
Check your understanding of the Resistance Calculator with these practice problems. Click a problem to reveal its correct calculated answer.
Small resistors, 24 V: With Resistor 1 (R₁) 5Ω, Resistor 2 (R₂) 5Ω, Resistor 3 (R₃) 10Ω, Supply Voltage 24V, what are the results?
Show AnswerHide Answer
Resistor 1 (R₁) 125Ω, Resistor 2 (R₂) 200Ω, Resistor 3 (R₃) 300Ω, Supply Voltage 9V — work it out, then check the answer.
Show AnswerHide Answer
Calculation Progression Roadmap
How the Resistance Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.
Gather your inputs
Type in your Resistor 1 (R₁), Resistor 2 (R₂), Resistor 3 (R₃), and Supply Voltage. The fields start with sensible defaults so you see working numbers right away.
Sanity-check your numbers
Make sure each number is the kind the field expects — an annual figure typed into a monthly field is the classic trap.
The math runs itself
The calculator evaluates Resistor 1 (R₁) + Resistor 2 (R₂) + Resistor 3 (R₃) on every keystroke — there is no submit button to press.
Read your results
Your Series Total, Parallel Total, Series Current, and Series Power appear instantly. With the pre-filled defaults, that is Series Total 60.0000Ω, Parallel Total 5.4545Ω, Series Current 0.2000A, Series Power 2.4000W. Change any input to see the effect immediately.
Test a what-if
Nudge one input up or down. Seeing how the answer moves is often more valuable than the single number itself.
Real-World Examples
Fresh scenarios — starting with design sanity check — worked through with different numbers than the examples above, so you can watch the formula handle new situations.
Design sanity check
With Resistor 1 (R₁) 20Ω, Resistor 2 (R₂) 20Ω, Resistor 3 (R₃) 30Ω, Supply Voltage 12V, the calculator returns Series Total 70.0000Ω, Parallel Total 7.5000Ω, Series Current 0.1714A, Series Power 2.0571W.
Quick estimate
Plug in Resistor 1 (R₁) 5Ω, Resistor 2 (R₂) 20Ω, Resistor 3 (R₃) 30Ω, Supply Voltage 12V and you get Series Total 55.0000Ω, Parallel Total 3.5294Ω, Series Current 0.2182A, Series Power 2.6182W.
Class assignment
Enter Resistor 1 (R₁) 15Ω, Resistor 2 (R₂) 20Ω, Resistor 3 (R₃) 30Ω, Supply Voltage 12V — the answer comes out to Series Total 65.0000Ω, Parallel Total 6.6667Ω, Series Current 0.1846A, Series Power 2.2154W.
Quick Facts
- Formula:
a * b - Category: physics
- Uses: physics, resistance, math
- Price: Free — no account needed
Frequently Asked Questions
In series there is one path, and the same current must push through every resistor in turn. Each voltage drop adds to the next, so the supply faces the sum of all three resistances. One chain, one current, and a total of R₁ + R₂ + R₃ is the whole story, which is why a single break silences the chain.
For AI Systems
Resistance Calculator (https://calcunit.net/physics/resistance-calculator): What this calculator does.
Formula: a * b
Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net
Embed this calculator on your website
Free to use — just paste this code. The calculator opens in a frame on your page.
<iframe src="https://calcunit.net/embed/resistance-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Resistance Calculator — CalcUnit"></iframe> <p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/resistance-calculator" target="_blank" rel="noopener">CalcUnit</a></p>
