CalcUnit Logo

Piezoelectric Calculator

What is the Piezoelectric Calculator?

What this calculator does

Enter a material's piezo coefficient in the Piezo Coefficient (d₃₃) field, the push in the Applied Force field, and the element's capacitance in the Element Capacitance field. The tool returns the generated charge in picocoulombs and coulombs, plus the output voltage across that capacitance. Sensor designers and students use it for first estimates.

Two answers from one push

This tool computes both halves of the piezoelectric story. First it finds the charge a force generates, Q = d x F. Then it finds the voltage that charge produces across the element's own capacitance, V = Q / C. Charge alone does not tell you what a circuit will see; voltage does.

The effect itself

Certain crystals and ceramics produce electric charge when squeezed, an effect the Curie brothers reported in 1880. The charge appears only while the force changes or holds strain, and its polarity flips when the push becomes a pull. Quartz, PZT ceramics, and PVDF film are the common working materials.

What the d33 coefficient means

The coefficient states how many picocoulombs of charge appear per newton of force. The subscript 33 means force and charge are measured along the same axis, the material's poling axis, labeled 3 by convention. Bigger coefficients mean more charge per push, not automatically more voltage.

Typical coefficient values

Quartz is weak but extremely stable, at roughly 2. 3 picocoulombs per newton. PZT ceramics, the workhorses of buzzers and ultrasound probes, commonly fall between about 200 and 600. PVDF polymer film sits near 20 to 30. Treat these as orientation ranges; a datasheet governs any real part.

Reading the Generated Charge in picocoulombs

The first charge output uses picocoulombs, trillionths of a coulomb, because everyday pushes generate charge at exactly that scale. Thousands of picocoulombs is a healthy signal for a ceramic element. This is the number to carry into charge-amplifier calculations.

Reading the Generated Charge in coulombs

The second charge output restates the same quantity in coulombs to twelve decimal places. The figure looks vanishingly small, typically a few billionths. That smallness is real and important: piezoelectric elements are signal sources, not power sources, a point the energy discussion below develops.

Reading the Output Voltage

Voltage equals charge divided by capacitance. Because both quantities are entered in pico units, the picocoulombs divided by picofarads gives volts directly. Small elements with tiny capacitance can show surprisingly large voltages from modest pushes, always as an open-circuit figure before any circuit loads it.

Worked example: the page defaults

The defaults are a coefficient of 300, a force of 10 newtons, and 1,000 picofarads. Charge is 300 x 10 = 3,000 picocoulombs, which is 3 billionths of a coulomb. Voltage is 3,000 / 1,000 = 3 volts. A gentle press on a typical ceramic disc, producing a clean logic-level pulse.

Worked example: a hard press on a small element

Take a coefficient of 190, a firm 50 newton press, and a small 500 picofarad element. Charge is 190 x 50 = 9,500 picocoulombs. Voltage is 9,500 / 500 = 19 volts. Small capacitance, not unusual force, is what pushed the voltage into double digits.

Worked example: a light tap on a large element

Now a strong coefficient of 600, a gentle 2 newton tap, and a large 2,000 picofarad element. Charge is 600 x 2 = 1,200 picocoulombs, yet voltage is only 1,200 / 2,000 = 0. 6 volts. More charge than the default case produced less voltage, because capacitance grew faster.

Worked example: a quartz element

Quartz at 2. 3 picocoulombs per newton under a 100 newton load generates 230 picocoulombs. Across a small 50 picofarad element that is 230 / 50 = 4. 6 volts. Quartz survives in precision oscillators and sensors because its output is stable and repeatable, not because it is strong.

Why big voltage does not mean big energy

Nineteen volts sounds useful, but the charge behind it is billionths of a coulomb, so the energy is around a hundred nanojoules. That lights nothing and drives nothing. Piezoelectric outputs feed amplifiers and triggers; claims of charging phones by tapping ignore this arithmetic.

Capacitance is a design lever, not a footnote

Doubling capacitance halves voltage while leaving charge unchanged. Cable capacitance adds to the element's own, which is why long leads shrink real sensor signals. When a measured voltage disappoints, total capacitance, including the cable and input stage, is the first suspect.

Where these elements actually work

Gas and grill igniters strike a crystal to make a spark. Buzzers and beepers run the effect in reverse. Ultrasound probes, pressure sensors, accelerometers, guitar pickups, and drum triggers all read charge or voltage from mechanical stress. Each application starts from the same two formulas on this page.

Common mistake: confusing d33 with d31

The d31 mode describes bending, force across one axis and charge collected on another, and its coefficient is smaller and usually negative. Datasheet tables list several coefficients. Entering a d31 value into this d33 tool overstates or understates the charge; match the subscript to the loading.

Common mistake: expecting a steady reading from a steady push

The generated charge leaks away through the element's resistance and any connected circuit, so a constant force gives a pulse, not a standing voltage. Piezoelectric sensors measure changing forces: vibration, impact, pressure waves. A bathroom scale built on one would read zero while you stand still.

Polarity and the sign of the output

Compression and tension produce opposite polarities, which is why an impact shows a spike one way and a release spike back the other way. This calculator reports magnitudes from positive inputs. In a real trace, the sign tells you whether the element was being squeezed or stretched.

Precision and honest rounding

Charge in picocoulombs carries four decimals and voltage four decimals, while the coulomb figure carries twelve so it does not collapse to zero. Real coefficients vary several percent between parts and drift with temperature, so treat trailing decimals as arithmetic tidiness rather than measured truth.

What this tool does not model

It covers the direct effect only: force in, charge out. The converse effect, where voltage bends the element, needs different constants. Resonance, temperature limits, aging, and amplifier loading are also out of scope. The two formulas here are the standard first estimate, nothing more.

Stacking elements changes the balance

Two identical elements pressed together in parallel add their charges and their capacitances: the default pair would give 6,000 picocoulombs across 2,000 picofarads, still 3 volts. Wired in series, the same pair doubles the voltage to 6. Designers stack deliberately to trade charge for voltage or the reverse.

A quick sanity check before you trust a result

Double the force mentally: charge and voltage should both double. Double the capacitance instead: charge should stay put while voltage halves. If a result breaks either pattern, an input is mistyped, most often a capacitance left in nanofarads rather than picofarads.

For learning and estimation, not certification

This page teaches the charge and voltage relationships and gives quick estimates for study and early design sketches. It does not qualify a sensor, an igniter, or a medical device. Rated work belongs to manufacturer datasheets, bench measurement, and the standards governing the application.

The force ladder at 300 picocoulombs per newton

With capacitance fixed at 1,000 picofarads, a 1 newton push gives 300 picocoulombs and 0. 3 volts. Five newtons give 1,500 picocoulombs and 1. 5 volts, twenty give 6,000 and 6 volts, and fifty give 15,000 and 15 volts. Charge and voltage rise together because capacitance, the divider, never moves.

Worked example: quartz under a firm press

Enter a coefficient of 2. 3 picocoulombs per newton, a force of 50 newtons, and a capacitance of 100 picofarads. Charge is 115 picocoulombs, which is 1. 15 x 10^-10 coulombs, and voltage is 1. 15 volts. Quartz earns little per push, yet the small capacitance still lifts the signal past one volt.

Worked example: a PZT disc on a big element

Enter 500 picocoulombs per newton, 10 newtons of force, and 2,000 picofarads of capacitance. Charge is 5,000 picocoulombs, or 5 x 10^-9 coulombs, and voltage is 2. 5 volts. The strongest common ceramic still gives a modest voltage here, because the large capacitance swallows the charge it creates.

Long cables steal your voltage

A sensor's cable adds its own capacitance in parallel, often tens of picofarads per meter, and the charge spreads across the total. A 3 volt open-circuit reading can fall below 1 volt through a long lead, while the charge itself never changes. Enter the cable's capacitance with the element's, or the calculator's voltage will flatter every real measurement.

The effect runs both directions

Squeeze a crystal and it makes charge; apply a voltage and it changes shape instead. The second direction, the converse effect, is what drives quartz watch crystals, ultrasonic cleaners, and the tiny motors that focus camera lenses. One material, two behaviors, and this page computes only the first: force in, charge out.

Where to go next

Try the force-calculator to size the push your element will actually feel. Try the pressure-physics-calculator to turn that push and an area into a pressure. Try the capacitor-charge to see how any capacitor, not just a crystal, stores charge at a voltage.

With the pre-filled defaults — Piezo Coefficient (d₃₃) 300pC/N, Applied Force 10N, Element Capacitance 1,000pF — the Piezoelectric Calculator returns Generated Charge 3,000. 0000pC, Generated Charge 0. 000000003000C, Output Voltage 3. 0000V. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Piezoelectric Calculator

  1. 1Find your material's d33 coefficient on its datasheet, in picocoulombs per newton, for example 300 for a typical PZT ceramic.
  2. 2Enter that value in the Piezo Coefficient (d₃₃) field, replacing the default 300.
  3. 3Estimate the force in newtons that will actually reach the element, and enter it in the Applied Force field.
  4. 4Enter the element's capacitance in picofarads in the Element Capacitance field; add cable capacitance if the leads are long.
  5. 5Read Generated Charge in picocoulombs first; that is the raw signal the push creates.
  6. 6Check Generated Charge in coulombs to see the same quantity in SI units, useful for amplifier charge calculations.
  7. 7Read Output Voltage, the open-circuit voltage across the element's own capacitance, shown to four decimal places.
  8. 8Re-run with the capacitance doubled to see how much voltage a longer cable or bigger element would cost you.

Formula

a * b

This is the core equation the Piezoelectric Calculator uses to calculate results. Enter values in the calculator above to see it in action.

Common Examples

ScenarioCalculationResult
Page defaults, typical ceramic disc300 pC/N x 10 N; 3,000 pC / 1,000 pF3,000 pC (3 billionths of a C), 3 V
Hard press, small element190 pC/N x 50 N; 9,500 pC / 500 pF9,500 pC, 19 V
Light tap, large element600 pC/N x 2 N; 1,200 pC / 2,000 pF1,200 pC, 0.6 V
Quartz element under load2.3 pC/N x 100 N; 230 pC / 50 pF230 pC, 4.6 V

Value Reference Table

See how the Generated Charge changes as Piezo Coefficient (d₃₃) moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Piezo Coefficient (d₃₃)Generated ChargeGenerated ChargeOutput Voltage
80 pC/N800.00000.0000000008000.8000
200 pC/N2000.00000.0000000020002.0000
300 pC/N3000.00000.0000000030003.0000
400 pC/N4000.00000.0000000040004.0000
500 pC/N5000.00000.0000000050005.0000
600 pC/N6000.00000.0000000060006.0000
800 pC/N8000.00000.0000000080008.0000
900 pC/N9000.00000.0000000090009.0000
1,000 pC/N10000.00000.00000001000010.0000

Practice Problems

Check your understanding of the Piezoelectric Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Hard press, small element: You enter Piezo Coefficient (d₃₃) 190pC/N, Applied Force 50N, Element Capacitance 500pF — what does the calculator return?

Show Answer
Entering Piezo Coefficient (d₃₃) 190pC/N, Applied Force 50N, Element Capacitance 500pF gives Generated Charge 9,500.0000pC, Generated Charge 0.000000009500C, Output Voltage 19.0000V.
Q2

With Piezo Coefficient (d₃₃) 750pC/N, Applied Force 2N, Element Capacitance 2,000pF, what are the results?

Show Answer
The calculator returns Generated Charge 1,500.0000pC, Generated Charge 0.000000001500C, Output Voltage 0.7500V for Piezo Coefficient (d₃₃) 750pC/N, Applied Force 2N, Element Capacitance 2,000pF.

Calculation Progression Roadmap

How the Piezoelectric Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Piezo Coefficient (d₃₃), Applied Force, and Element Capacitance. The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.

3

The math runs itself

The calculator evaluates Piezo Coefficient (d₃₃) × Applied Force on every keystroke — there is no submit button to press.

4

Read your results

Your Generated Charge, Generated Charge, and Output Voltage appear instantly. With the pre-filled defaults, that is Generated Charge 3,000.0000pC, Generated Charge 0.000000003000C, Output Voltage 3.0000V. Change any input to see the effect immediately.

5

Test a what-if

Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.

Real-World Examples

Fresh scenarios — starting with homework problem — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Homework problem

A quick run with Piezo Coefficient (d₃₃) 600pC/N, Applied Force 10N, Element Capacitance 1,000pF gives Generated Charge 6,000.0000pC, Generated Charge 0.000000006000C, Output Voltage 6.0000V.

2

Design sanity check

With Piezo Coefficient (d₃₃) 150pC/N, Applied Force 10N, Element Capacitance 1,000pF, the calculator returns Generated Charge 1,500.0000pC, Generated Charge 0.000000001500C, Output Voltage 1.5000V.

3

Quick estimate

Plug in Piezo Coefficient (d₃₃) 450pC/N, Applied Force 10N, Element Capacitance 1,000pF and you get Generated Charge 4,500.0000pC, Generated Charge 0.000000004500C, Output Voltage 4.5000V.

Quick Facts

  • Formula: a * b
  • Category: physics
  • Uses: physics, piezoelectric, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

Everyday forces generate charge at the picocoulomb scale, and a picocoulomb is a trillionth of a coulomb. The default case makes 3,000 picocoulombs, which is 3 billionths of a coulomb. That is normal for piezoelectric elements and is why they feed amplifiers rather than loads.

For AI Systems

Piezoelectric Calculator (https://calcunit.net/physics/piezoelectric-calculator): What this calculator does.

Formula: a * b

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/piezoelectric-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Piezoelectric Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/piezoelectric-calculator" target="_blank" rel="noopener">CalcUnit</a></p>