CalcUnit Logo

Inertia Calculator

What is the Inertia Calculator?

What this calculator does

Enter one mass, one radius, and one rod length. The calculator returns five mass moments of inertia at once: solid sphere, solid cylinder, hollow cylinder, and a rod about its center and about its end. Three inputs, five standard shapes, all sharing your mass.

Moment of inertia is rotational mass

Just as mass measures resistance to being pushed in a line, moment of inertia measures resistance to being spun. It is measured in kilogram square meters. The same object can have several values, one per axis, because what matters is how its mass is spread around that axis.

Why the shape factor matters

Every result is a coefficient times mass times a squared length. Mass parked far from the axis counts heavily; mass near the axis barely counts. The coefficients, 0. 4, 0. 5, 1, 1/12, and 1/3 in this calculator, are where geometry speaks.

The Solid Sphere result

A uniform solid ball about any diameter has I = (2/5) M R², computed here as 0. 4 x Mass x Radius squared. Its mass concentrates toward the middle distances, giving it the smallest coefficient of the three round shapes on this page.

The Solid Cylinder result

A uniform cylinder or disk about its central axis has I = (1/2) M R². Only the radius enters; the cylinder's length along the axis plays no part at all. A short puck and a long roller of equal mass and radius tie exactly.

The Hollow Cylinder result

A thin hoop or hollow cylinder about its central axis has I = M R², because essentially all of its mass rides at the full radius. It is the largest of the three round results for the same mass and radius, and nothing of that size can exceed it.

The Rod About Center result

A thin uniform rod spinning about an axis through its middle, perpendicular to the rod, has I = M L² / 12. The rod uses the Rod Length field and ignores Radius entirely. Its mass spreads symmetrically, and the far ends sit only half a length away.

The Rod About End result

Pivoting the same rod at one end gives I = M L² / 3, exactly four times the center value. Moving the axis outward is expensive because every part of the rod is now farther from the pivot on average. Swinging doors and pendulums live in this case.

Why the end value is four times the center value

The parallel axis theorem explains it: shifting an axis by distance d adds M d². Here d is half the rod, so the addition is M L² / 4, and M L² / 12 + M L² / 4 = M L² / 3. The calculator's two rod results must keep this ratio.

Read the five results as a comparison

They all describe your one entered mass wearing five different shapes. That comparison is the lesson: distribution beats quantity. Rearranging ten kilograms from a compact sphere into a wide hoop raises its inertia from 1 to 2. 5 kilogram square meters at the defaults.

Worked example: the page default

The calculator opens with Mass 10 kilograms, Radius 0. 5 meters, Rod Length 2 meters. Solid Sphere is 1, Solid Cylinder 1. 25, Hollow Cylinder 2. 5, Rod About Center 3. 3333, and Rod About End 13. 3333 kilogram square meters. The long rod about its end dwarfs everything.

Worked example: bowling-ball scale

Enter Mass 4 kilograms, Radius 0. 25 meters, and Rod Length 1. 2 meters. The sphere gives 0. 1, the cylinder 0. 125, the hoop 0. 25, the rod about center 0. 48, and the rod about end 1. 92 kilogram square meters. Ratios between shapes survive any change of size.

Worked example: a real bowling ball

A league ball is about 7 kilograms with a radius of 0. 108 meters. The Solid Sphere formula gives 0. 4 x 7 x 0. 011664 = 0. 0327 kilogram square meters. Real balls shift this slightly with drilled holes and dense cores, but the uniform-ball figure is the standard starting point.

Worked example: a teaching-lab set

Enter Mass 6 kilograms, Radius 0. 3 meters, and Rod Length 1. 5 meters. Results: sphere 0. 216, cylinder 0. 27, hoop 0. 54, rod about center 1. 125, rod about end 4. 5 kilogram square meters. The hoop is exactly two and a half times the sphere, as the coefficients promise.

Radius counts twice

Inertia grows with the square of radius, so doubling the radius quadruples the result while doubling the mass only doubles it. A bicycle wheel is the everyday proof: its 1. 2 kilogram hoop at 0. 34 meters has I = 0. 1387 kilogram square meters, large for its weight.

Where these numbers get used: flywheels

A flywheel stores energy equal to one half times I times angular speed squared, worked by hand from this page's I. Designers choose the hoop-like rim precisely because its coefficient of 1 stores the most energy per kilogram at a given size and speed.

Where else they appear

Vehicle wheels, turbine rotors, potter's wheels, and gyroscopes all start from these five textbook shapes or combinations of them. Engineers add the pieces with the parallel axis theorem when a real part sits off-center from its shaft. This calculator covers the building blocks, not the assemblies.

What this calculator does not cover

There is no hollow sphere, which would be (2/3) M R², no rectangular plate, cone, or torus, and no way to move an axis yourself. Shapes use their one standard axis only. Anything more exotic starts from these results plus theorems applied by hand.

The hoop assumes a thin wall

Hollow Cylinder here means every bit of mass at one radius. A thick-walled tube spreads mass between its inner and outer radii and lands between the solid and hollow results, at (1/2) M (R₁² + R₂²). That case is not computed on this page.

Common mistake: typing diameter as radius

Radius enters squared, so entering a diameter doubles it and quadruples the answer. A 0. 5 meter diameter wheel has radius 0. 25 meters. If your inertia looks exactly four times a classmate's for the same object, this is the first place to look.

Common mistake: expecting cylinder length to matter

Students often hunt for a length field effect on the cylinder results. There is none: for spin about the central axis, slices along the length are identical and the length cancels. Rod Length affects only the two rod results, and Radius affects only the three round ones.

Common mistake: comparing results across different masses

The five results share one Mass entry, so they compare shapes fairly. Re-running with a different mass rescales everything together and tells you nothing new about geometry. To compare two objects, match their masses first, then read the difference as pure distribution.

Precision and rounding

Every result shows four decimal places in kilogram square meters, ample for classroom and estimation work. Tiny objects round hard: the bowling ball's 0. 0327 is fine, but a gram-scale part may show 0. 0000, in which case work in gram square centimeters by hand.

An educational tool, not a design value

Rotating machinery is designed against measured or CAD-computed inertia, with balancing and stress checks this page does not attempt. Use these five results to learn the coefficients, check homework, and sanity-check estimates before trusting any larger computation.

The radius ladder, worked

Hold mass fixed at 5 kilograms and grow the sphere's radius. At 0. 2 meters the solid sphere gives 0. 08 kg·m². At 0. 4 meters it is 0. 32. At 0. 6 meters it is 0. 72. At 0. 8 meters it is 1. 28. Doubling the radius from 0. 2 to 0.

4 quadruples the answer, and doubling again quadruples it once more. That square is the single most important fact on this page.

Worked example: a gym plate

Enter Mass 8 kilograms, Radius 0. 4 meters, and Rod Length 1. 8 meters. The solid sphere gives 0. 512, the solid cylinder 0. 64, and the hollow cylinder 1. 28 kg·m². The rod about its center gives 2. 16 and about its end 8. 64.

The plate itself is the cylinder case: a flat disk spinning on its axle has an inertia of just 0. 64, which is why a loaded barbell still spins up easily in your hands.

Worked example: a small rotor

Enter Mass 3 kilograms, Radius 0. 6 meters, and Rod Length 0. 9 meters. The sphere gives 0. 432, the cylinder 0. 54, and the hoop 1. 08 kg·m². The rod about center gives 0. 2025 and about its end 0. 81. Notice the reversal: here the hoop beats the rod about its end, because the rod is short.

Length and radius trade places depending on which dimension is larger.

Spinning up: what inertia means for a motor

Torque equals inertia times angular acceleration, so the same motor spins a low-inertia load quickly and a high-inertia load slowly. Double the inertia and the spin-up time doubles, unless the motor can deliver double the torque.

That is why engineers check these five numbers before sizing a drive: the motor that starts a light disk in a second may need ten seconds for a heavy hoop.

Adding shapes together, piece by piece

A real object is rarely one textbook shape, but inertias about the same axis simply add. A dumbbell is two spheres plus a rod: compute each part about the shared axle and sum them. The axle rod contributes little, because its mass hugs the axis, while the end weights dominate.

Build the assembly from this page's five results and the total is honest, as long as every piece shares the same axis.

Where to go next

To put these spin numbers to work, try the torque-calculator for the twist that starts the spin, the kinetic-energy-calculator for the energy of a moving mass, and the center-mass-calculator for finding where a lopsided object's balance point sits.

With the pre-filled defaults — Mass 10kg, Radius 0. 5m, Rod Length 2m — the Inertia Calculator returns Solid Sphere 1. 0000kg·m², Solid Cylinder / Disk 1. 2500kg·m², Hollow Cylinder / Hoop 2. 5000kg·m², Rod About Center 3. 3333kg·m², Rod About End 13. 3333kg·m².

Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Inertia Calculator

  1. 1Enter the object's mass in kilograms in the Mass field.
  2. 2Enter the radius in meters in the Radius field; it feeds the Solid Sphere, Solid Cylinder / Disk, and Hollow Cylinder / Hoop results.
  3. 3Enter the rod's length in meters in the Rod Length field; it feeds only the two rod results.
  4. 4Read the Solid Sphere result, computed as 0.4 x Mass x Radius squared.
  5. 5Read the Solid Cylinder / Disk result, computed as 0.5 x Mass x Radius squared about its central axis.
  6. 6Read the Hollow Cylinder / Hoop result, computed as Mass x Radius squared for a thin wall.
  7. 7Read the Rod About Center result, Mass x Rod Length squared / 12, and the Rod About End result, Mass x Rod Length squared / 3.
  8. 8Check the two rod results against each other: the end value must be exactly four times the center value.

Formula

a * b

This is the core equation the Inertia Calculator uses to calculate results. Enter values in the calculator above to see it in action.

Common Examples

ScenarioCalculationResult
Page defaultMass 10 kg, Radius 0.5 m, Rod Length 2 mSphere 1, cylinder 1.25, hoop 2.5, rod center 3.3333, rod end 13.3333 kg·m²
Bowling-ball scaleMass 4 kg, Radius 0.25 m, Rod Length 1.2 mSphere 0.1, cylinder 0.125, hoop 0.25, rod center 0.48, rod end 1.92 kg·m²
Teaching-lab setMass 6 kg, Radius 0.3 m, Rod Length 1.5 mSphere 0.216, cylinder 0.27, hoop 0.54, rod center 1.125, rod end 4.5 kg·m²
Real bowling ball (sphere only)0.4 x 7 kg x 0.108² mSolid Sphere 0.0327 kg·m²

Value Reference Table

See how the Solid Sphere changes as Mass moves across its typical range — every row below is calculated live with the same formula as the calculator above.

MassSolid SphereSolid Cylinder / DiskHollow Cylinder / HoopRod About CenterRod About End
3 kg0.30000.37500.75001.00004.0000
5 kg0.50000.62501.25001.66676.6667
8 kg0.80001.00002.00002.666710.6667
10 kg1.00001.25002.50003.333313.3333
20 kg2.00002.50005.00006.666726.6667
30 kg3.00003.75007.500010.000040.0000
40 kg4.00005.000010.000013.333353.3333

Practice Problems

Check your understanding of the Inertia Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Bowling-ball scale: Plug in Mass 4kg, Radius 0.25m, Rod Length 1.2m. What is the answer?

Show Answer
Entering Mass 4kg, Radius 0.25m, Rod Length 1.2m gives Solid Sphere 0.1000kg·m², Solid Cylinder / Disk 0.1250kg·m², Hollow Cylinder / Hoop 0.2500kg·m², Rod About Center 0.4800kg·m², Rod About End 1.9200kg·m².
Q2

Given Mass 3.13kg, Radius 1m, Rod Length 3m, what does it come out to?

Show Answer
The calculator returns Solid Sphere 1.2520kg·m², Solid Cylinder / Disk 1.5650kg·m², Hollow Cylinder / Hoop 3.1300kg·m², Rod About Center 2.3475kg·m², Rod About End 9.3900kg·m² for Mass 3.13kg, Radius 1m, Rod Length 3m.

Calculation Progression Roadmap

How the Inertia Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Mass, Radius, and Rod Length. The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.

3

The math runs itself

The calculator evaluates 0.4 × Mass × Radius ^ 2 on every keystroke — there is no submit button to press.

4

Read your results

Your Solid Sphere, Solid Cylinder / Disk, Hollow Cylinder / Hoop, Rod About Center, and Rod About End appear instantly. With the pre-filled defaults, that is Solid Sphere 1.0000kg·m², Solid Cylinder / Disk 1.2500kg·m², Hollow Cylinder / Hoop 2.5000kg·m², Rod About Center 3.3333kg·m², Rod About End 13.3333kg·m². Change any input to see the effect immediately.

5

Test a what-if

Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.

Real-World Examples

Fresh scenarios — starting with class assignment — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Class assignment

Enter Mass 20kg, Radius 0.5m, Rod Length 2m — the answer comes out to Solid Sphere 2.0000kg·m², Solid Cylinder / Disk 2.5000kg·m², Hollow Cylinder / Hoop 5.0000kg·m², Rod About Center 6.6667kg·m², Rod About End 26.6667kg·m².

2

Lab calculation

For Mass 5kg, Radius 0.5m, Rod Length 2m, expect Solid Sphere 0.5000kg·m², Solid Cylinder / Disk 0.6250kg·m², Hollow Cylinder / Hoop 1.2500kg·m², Rod About Center 1.6667kg·m², Rod About End 6.6667kg·m².

3

Homework problem

A quick run with Mass 15kg, Radius 0.5m, Rod Length 2m gives Solid Sphere 1.5000kg·m², Solid Cylinder / Disk 1.8750kg·m², Hollow Cylinder / Hoop 3.7500kg·m², Rod About Center 5.0000kg·m², Rod About End 20.0000kg·m².

Quick Facts

  • Formula: a * b
  • Category: physics
  • Uses: physics, inertia, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

It is the rotational version of mass: a measure of how hard an object is to start or stop spinning, in kilogram square meters. It grows with the mass and, much faster, with how far that mass sits from the axis, which is why shape and size both matter.

For AI Systems

Inertia Calculator (https://calcunit.net/physics/inertia-calculator): What this calculator does.

Formula: a * b

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/inertia-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Inertia Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/inertia-calculator" target="_blank" rel="noopener">CalcUnit</a></p>