CalcUnit Logo

Electric Field Calculator

What is the Electric Field Calculator?

What this calculator does

Enter one Source Charge (Q), a Distance (r), and a Test Charge (q), and it returns the Field Strength (E), the Force on Test Charge, and the Electric Potential (V) at that distance. The model is a single point charge in empty space. Nothing else is hiding inside it.

A field is force waiting to happen

A charge reshapes the space around it. The electric field at a point states how hard a tiny positive charge placed there would be pushed, per unit of its charge. Measure it in newtons per coulomb, and you know the push before any test charge actually arrives.

Coulomb's constant and where it comes from

The formulas use k = 8. 99 x 10^9 newton square meters per square coulomb, the rounded classroom value of Coulomb's constant. The CODATA figure maintained through NIST is 8. 987551787 x 10^9, about 0. 03 percent lower. Every result on this page therefore runs a hair high, by an amount no homework will ever notice.

The inverse-square law runs the show

Field strength falls with the square of the distance. Double the distance and the field quarters; halve it and the field quadruples. With the default charge, the field at 0. 5 meters is 35,960 newtons per coulomb, and at 0. 25 meters it is 143,840. That steep falloff shapes everything from sparks to sensor design.

Potential fades more gently

Electric potential falls with the first power of distance, not the square, because potential measures accumulated work along a path rather than local push. It is a scalar in volts, with no direction. At twice the distance the field is a quarter as strong, but the potential is merely halved.

Reading the three results

Field Strength (E) prints to four decimal places in newtons per coulomb. Force on Test Charge prints to six decimal places in newtons, because forces on small charges are tiny fractions. Electric Potential (V) prints to four decimals in volts. Negative values carry meaning and are explained below.

Worked example: the page defaults

A source charge of 1 microcoulomb, a distance of 0. 5 meters, and a test charge of 1 nanocoulomb return a field of 35,960 newtons per coulomb, a force of 0. 000036 newtons, and a potential of 17,980 volts. The force is about the weight of a few grains of sand, spread on almost nothing.

Worked example: a small charge up close

Shrink the source to 5 nanocoulombs and move in to 0. 1 meters, with a test charge of 2 nanocoulombs. The field is 4,495 newtons per coulomb, the force 0. 00000899 newtons, and the potential 449. 5 volts. Small charges make respectable fields at small distances, thanks to the inverse-square law working in reverse.

Worked example: a negative source charge

Enter negative 3 microcoulombs at 2 meters with a test charge of 4 nanocoulombs. The field reads negative 6,742. 5 newtons per coulomb and the potential negative 13,485 volts. The minus signs say the field points inward, toward the source, and a positive test charge is pulled in, not pushed away.

Worked example: one proton at one angstrom

Set the source to 1. 6 x 10^-19 coulombs, roughly one elementary charge, at a distance of 10^-10 meters, one angstrom. The field is 1. 4384 x 10^11 newtons per coulomb and the potential 14. 384 volts. Fields inside atoms are colossal, which is why chemistry, an angstrom-scale science, is an electrical science.

What the signs mean

The sign of the field follows the source charge: positive sources push outward, negative sources pull inward. The sign of the force follows both charges multiplied together, so a negative test charge in a positive field feels a force toward the source. The calculator keeps the signs; reading them correctly is your job.

The test charge must stay a guest

The whole model assumes the test charge is too small to disturb the source. A nanocoulomb test charge near a microcoulomb source respects that bargain. Enter a test charge rivaling the source and the arithmetic still runs, but the physical picture, one fixed source probed gently, no longer describes any real arrangement.

How strong is strong

Dry air itself breaks down near 3,000,000 newtons per coulomb, turning insulator into spark. The default example's 35,960 is about one percent of that. Fields at the surface of a charged balloon or a Van de Graaff dome live in the hundreds of thousands, dramatic to hair and dust yet far below breakdown.

One charge only

There is no second source, no charged plate, and no field-line drawing. Two charges demand vector addition of two fields, which this page will not do. The uniform field between parallel plates follows a different relation entirely, field equals voltage divided by plate spacing, and belongs on a different page.

Entering tiny charges

Charges in real problems arrive as microcoulombs and nanocoulombs. Convert before typing: 1 microcoulomb is 1 x 10^-6 coulombs and 1 nanocoulomb is 1 x 10^-9. Number fields accept scientific notation, so typing 1e-6 into Source Charge (Q) is cleaner and far less error-prone than counting zeros in 0. 000001.

Common mistake: distance in centimeters

The Distance (r) field wants meters. Ten centimeters is 0. 1 meters, and typing 10 instead makes the distance a hundred times too large and the field ten thousand times too small, because the distance is squared. A result that looks suspiciously feeble usually traces back to this slip.

Field and potential are different animals

Students conflate them because both come from the same charge. Keep them apart: the field is a push per unit charge, a vector strength at a point; the potential is stored work per unit charge, a scalar height. Water pressure versus water depth is the household analogy, imperfect but useful.

Precision and rounding

The force line's six decimals exist because the numbers are small: 0. 000036 newtons is the default force, and four decimals would erase it to 0. 0000. If your force still prints as zero, your charges are extraordinarily small, and scientific notation by hand will serve you better than this readout.

Where the model earns its keep

Introductory electrostatics, ion and electron optics estimates, and sensor back-of-envelope work all lean on the point-charge formulas. They are exact for a spherically symmetric charge viewed from outside it, by the shell theorem, which is why a charged metal sphere can be treated as a point at its center.

The one-meter coincidence

Set the distance to exactly 1 meter and the field and potential print the same digits, as with a 2 microcoulomb source giving 17,980 for both. It is a numerical accident of that one distance, not a physical identity: the units differ, and at every other distance the two numbers part ways.

An educational tool, with the model stated

Real electrodes have shapes, edges concentrate fields, and nearby matter polarizes. Use this calculator to learn the point-charge relationships and check coursework. For high-voltage design clearances or safety work, field simulation and the governing electrical codes, not a three-input web page, are the authority.

Worked example: four microcoulombs at arm's length

Place a source charge of 4 microcoulombs, typed as 0. 000004, at a distance of 0. 4 meters, with a test charge of 3 nanocoulombs. The field is 224,750 newtons per coulomb, the force on the test charge is 0. 000674 newtons, and the potential is 89,900 volts.

The field is more than six times the page default, because the charge is four times larger and the distance a little shorter, and the inverse-square law multiplies both effects at once. The force is still tiny, about the weight of a small grain of sand, because the test charge is only 3 nanocoulombs.

Worked example: a negative source pulls inward

Enter a source charge of negative 8 microcoulombs at 1. 2 meters, with a test charge of 5 nanocoulombs. The field reads negative 49,944. 4444 newtons per coulomb, the force negative 0. 000250 newtons, and the potential negative 59,933. 3333 volts.

Every minus sign points the same way: the field aims toward the source, and a positive test charge is pulled in rather than pushed away. Flip the source sign to positive and all three results flip with it, which is the quickest sanity check on this page.

A ladder of distances for one charge

Fix the source at 5 microcoulombs and step away from it

At 0. 5 meters the field is 179,800 newtons per coulomb. At 1 meter it falls to 44,950. At 2 meters it is 11,237. 5, and at 4 meters only 2,809. 375.

Each doubling of distance quarters the field, exactly as the inverse-square law promises, so moving from half a meter to four meters cuts the field by a factor of 64. That steep fall is why static cling is a close-range effect and why a charged comb stops attracting paper the moment you pull it a few inches away.

Where to go next

The Coulomb Law Calculator finds the force directly between two charges

The Field Strength Calculator covers uniform fields such as the one between parallel plates. The Electric Power Calculator turns voltage and current into watts for the circuits these charges eventually feed. The Magnetic Field Calculator handles the magnetic side of moving charge.

With the pre-filled defaults — Source Charge (Q) 0. 000001 C, Distance (r) 0. 5 m, Test Charge (q) 0 C — the Electric Field Calculator returns Field Strength (E) 35,960. 0000 N/C, Force on Test Charge 0. 000036 N, Electric Potential (V) 17,980. 0000 V.

Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Electric Field Calculator

  1. 1Enter the source charge, in coulombs, in the Source Charge (Q) field; 1 microcoulomb is typed as 1e-6.
  2. 2Enter the straight-line distance from the charge, in meters, in the Distance (r) field.
  3. 3Enter the charge you are placing at that distance, in coulombs, in the Test Charge (q) field.
  4. 4Read the Field Strength (E) result in newtons per coulomb.
  5. 5Read the Force on Test Charge result in newtons; its sign tells you attraction versus repulsion.
  6. 6Read the Electric Potential (V) result in volts.
  7. 7Halve the Distance (r) value and watch the field quadruple while the potential only doubles; that contrast is the lesson.
  8. 8Try a negative Source Charge (Q) to model an electron-like source and watch the field and potential flip sign.

Formula

a * b

This is the core equation the Electric Field Calculator uses to calculate results. Enter values in the calculator above to see it in action.

Common Examples

ScenarioCalculationResult
The page defaultsQ = 1e-6 C, r = 0.5 m, q = 1e-9 C: E = 8.99e9 x 1e-6 / 0.25 = 35,960 N/C; F = 35,960 x 1e-9 = 0.000036 N; V = 8.99e9 x 1e-6 / 0.5 = 17,980 V.Field Strength 35,960.0000 N/C; Force on Test Charge 0.000036 N; Electric Potential 17,980.0000 V.
Small charge, close distanceQ = 5e-9 C, r = 0.1 m, q = 2e-9 C: E = 8.99e9 x 5e-9 / 0.01 = 4,495 N/C; F = 4,495 x 2e-9 = 0.00000899 N; V = 8.99e9 x 5e-9 / 0.1 = 449.5 V.Field Strength 4,495.0000 N/C; Force on Test Charge 0.000009 N; Electric Potential 449.5000 V.
Negative source chargeQ = -3e-6 C, r = 2 m, q = 4e-9 C: E = 8.99e9 x -3e-6 / 4 = -6,742.5 N/C; F = -6,742.5 x 4e-9 = -0.000027 N; V = 8.99e9 x -3e-6 / 2 = -13,485 V.Field Strength -6,742.5000 N/C; Force on Test Charge -0.000027 N; Electric Potential -13,485.0000 V.
One proton at one angstromQ = 1.6e-19 C, r = 1e-10 m, q = 1.6e-19 C: E = 8.99e9 x 1.6e-19 / 1e-20 = 1.4384 x 10^11 N/C; F = 1.4384e11 x 1.6e-19 = 2.30144 x 10^-8 N; V = 8.99e9 x 1.6e-19 / 1e-10 = 14.384 V.Field Strength 143,840,000,000.0000 N/C; Force on Test Charge 0.000000 N at six decimals; Electric Potential 14.3840 V.

Value Reference Table

See how the Field Strength (E) changes as Source Charge (Q) moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Source Charge (Q)Field Strength (E)Force on Test ChargeElectric Potential (V)
0 C10788.00000.0000115394.0000
0 C17980.00000.0000188990.0000
0 C28768.00000.00002914384.0000
0 C35960.00000.00003617980.0000
0 C71920.00000.00007235960.0000
0 C107880.00000.00010853940.0000
0 C143840.00000.00014471920.0000

Practice Problems

Check your understanding of the Electric Field Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

2 µC at 1 m: Plug in Source Charge (Q) 0.000002 C, Distance (r) 1 m, Test Charge (q) 0 C. What is the answer?

Show Answer
Entering Source Charge (Q) 0.000002 C, Distance (r) 1 m, Test Charge (q) 0 C gives Field Strength (E) 17,980.0000 N/C, Force on Test Charge 0.000018 N, Electric Potential (V) 17,980.0000 V.
Q2

Given Source Charge (Q) 0 C, Distance (r) 0.1 m, Test Charge (q) 0 C, what does it come out to?

Show Answer
The calculator returns Field Strength (E) 0.0000 N/C, Force on Test Charge 0.000000 N, Electric Potential (V) 0.0000 V for Source Charge (Q) 0 C, Distance (r) 0.1 m, Test Charge (q) 0 C.

Calculation Progression Roadmap

How the Electric Field Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Source Charge (Q), Distance (r), and Test Charge (q). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.

3

The math runs itself

The calculator evaluates 8.99e9 × Source Charge (Q) ÷ Distance (r)^2 on every keystroke — there is no submit button to press.

4

Read your results

Your Field Strength (E), Force on Test Charge, and Electric Potential (V) appear instantly. With the pre-filled defaults, that is Field Strength (E) 35,960.0000 N/C, Force on Test Charge 0.000036 N, Electric Potential (V) 17,980.0000 V. Change any input to see the effect immediately.

5

Test a what-if

Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.

Quick Facts

  • Formula: a * b
  • Category: physics
  • Uses: physics, electric field, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

It is the proportionality constant in Coulomb's law, set by how strongly charges interact in vacuum. The CODATA value maintained through NIST is 8. 987551787 x 10^9 newton square meters per square coulomb. This calculator uses the rounded 8. 99 x 10^9 found in most textbooks, which raises results by about 0. 03 percent.

For AI Systems

Electric Field Calculator (https://calcunit.net/physics/electric-field-calculator): What this calculator does.

Formula: a * b

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/electric-field-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Electric Field Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/electric-field-calculator" target="_blank" rel="noopener">CalcUnit</a></p>