CalcUnit Logo

Capacitor Charge Calculator

What is the Capacitor Charge Calculator?

What this calculator does

Pick one of three modes and the calculator solves for charge, capacitance, or voltage in a capacitor, using the relation Q = C x V. Electronics students, hobbyists, and technicians use it to move between a capacitor's rating and the charge it actually holds at a working voltage.

One equation, three questions

Charge, capacitance, and voltage are locked together: knowing any two fixes the third. The Calculate selector at the top chooses which quantity is the answer. Mode 1 finds charge from capacitance and voltage; Mode 2 finds capacitance from charge and voltage; Mode 3 finds voltage from charge and capacitance.

Capacitance is charge per volt

A capacitor's capacitance states how much charge its plates hold for each volt applied. One farad means one coulomb per volt, a very large amount, which is why real components are rated in microfarads and picofarads and why the entries here are usually small decimals.

Reading the Computed Value result

The single Computed Value field in the Result group shows the answer to six decimal places. It carries no unit label of its own, so the mode you selected supplies the meaning: coulombs in Mode 1, farads in Mode 2, volts in Mode 3. Note the mode before you note the number.

Mode 1: solving for charge

Charge equals capacitance times voltage. With the page defaults, a capacitance of 0. 0001 farads at 12 volts holds a charge of 0. 001200 coulombs. This is the mode for questions like how much charge a filter capacitor stores at its rail voltage.

Mode 2: solving for capacitance

Capacitance equals charge divided by voltage. Entering a charge of 0. 0012 coulombs measured at 12 volts returns 0. 000100 farads, recovering the component's rating. This mode suits lab work where charge is what an experiment measures and the capacitance is the unknown.

Mode 3: solving for voltage

Voltage equals charge divided by capacitance. A charge of 0. 0012 coulombs on 0. 0001 farads gives 12. 000000 volts, exactly undoing the first mode. Use this mode to find how high the voltage climbs when a known charge is pushed onto a small capacitor.

Worked example: the page defaults round trip

The three modes are consistent by construction. Mode 1 with the defaults produces 0. 001200 coulombs. Feeding that charge into Mode 3 with the same capacitance returns 12. 000000 volts, and Mode 2 with that charge and voltage returns 0. 000100 farads. Cycling all three is a quick self-check.

Worked example: a camera flash capacitor

A photoflash capacitor of 200 microfarads, entered as 0. 0002 farads, charged to 330 volts holds 0. 066000 coulombs. That modest charge, released in a fraction of a millisecond, is what makes the flash so intense; the calculator gives the charge, and the short discharge time explains the punch.

Worked example: a power-supply filter

A large filter capacitor of 10,000 microfarads is 0. 01 farads. At a 25-volt rail it stores 0. 250000 coulombs. Big electrolytic capacitors like this one smooth the ripple in power supplies, and their charge figures show why they must be discharged carefully before servicing equipment.

Worked example: a motor start capacitor

A 470-microfarad start capacitor, 0. 00047 farads, on a 50-volt circuit holds 0. 023500 coulombs. Motor technicians meet numbers like these when checking whether a start capacitor still matches its nameplate, since capacitance fades as electrolytics age and dry out.

The farad is enormous

One farad stores a full coulomb per volt, more than most circuits ever handle, so component values are quoted in microfarads, millionths of a farad, or smaller. The conversion discipline matters more than the arithmetic: 100 microfarads is 0. 0001 farads, and misplacing that factor ruins every mode equally.

Common mistake: entering microfarads as written

The Capacitance field expects farads, so a part marked 100 must be entered as 0. 0001, not 100. Entering the printed microfarad number directly inflates charge or deflates voltage by a factor of one million. Convert every nameplate value before it touches the keyboard.

The calculator reads only two inputs

Each mode's formula uses exactly two of the three fields, and the third is ignored. In Mode 1 the Charge field plays no part; in Mode 2 the Capacitance field plays no part; in Mode 3 the Voltage field plays no part. Leftover numbers from an earlier calculation cannot contaminate the result.

What this calculator does not do: energy

There is no energy output anywhere on this page. The stored energy, one half times capacitance times voltage squared, must be worked by hand. For the page defaults it is 0. 5 x 0. 0001 x 144 = 0. 0072 joules. The flash capacitor above stores 10. 89 joules by the same hand calculation.

What else it does not do

Series and parallel combinations, charging time through a resistor, and reactance at a given frequency all live outside this page. Those problems begin from the charge, capacitance, and voltage found here, then apply their own formulas for equivalent capacitance, the RC time constant, or capacitive reactance.

Six decimal places, and their limit

The result shows six decimal places, which is generous for volt-scale answers but tight for tiny charges. A 0. 47-microfarad capacitor at 5 volts holds 0. 00000235 coulombs, which displays as 0. 000002. For picofarad parts the display can round a real charge almost away, so scale your expectations accordingly.

Charge is not current

Coulombs measure accumulated charge; amperes measure charge flowing per second. A capacitor holding 0. 250000 coulombs can deliver it as a brief, heavy surge or a long, gentle leak. This calculator describes the reservoir, not the flow, and confusing the two leads to badly wrong expectations.

The charge lives on two plates

The charge this calculator returns is the charge separated onto the plates: positive on one, negative on the other, equal in size. The capacitor as a whole stays neutral. That stored separation, held apart by the insulating layer between the plates, is what later flows back as current.

Worked example: a supercapacitor cell

Modern supercapacitors are the exception to the tiny-farad rule, with single cells rated in whole farads. A 3,000-farad cell at its 2. 7-volt rating holds 3,000 x 2. 7 = 8,100. 000000 coulombs in Mode 1. Such cells buffer buses and cranes through brief power interruptions.

Voltage rating is a ceiling

Every real capacitor carries a maximum voltage, set by the thin insulating layer between its plates. Exceed it and the layer breaks down, often destroying the part. The voltage in these formulas is the voltage actually applied, which should stay at or below the rating with margin.

Real capacitors leak their charge

The insulating layer is not perfect, so a charged capacitor slowly loses its charge even with nothing connected, over hours or days depending on the type. The formulas here describe the ideal moment of charging. Measurements taken long after disconnecting a part will read lower than Mode 1 predicts.

Where these numbers show up

Camera flashes, power-supply smoothing, motor starting, timing circuits, and touch sensors all reduce to charge on capacitance at some voltage. The three modes here cover the everyday algebra among those three quantities, which is most of what bench troubleshooting asks for.

Worked example: a defibrillator capacitor.

A hospital defibrillator stores its shock in a capacitor of about 32 microfarads, charged to roughly 5,000 volts. Enter 0. 000032 farads and 5,000 volts in Mode 1 and the calculator returns 0. 160000 coulombs.

The stored energy, worked by hand as one half times capacitance times voltage squared, is 400 joules, which is the scale of energy a defibrillator delivers to restart a heart.

Worked example: a timing circuit on a 9-volt battery.

A small timing circuit runs from a 9-volt battery through a 22-microfarad capacitor. Enter 0. 000022 farads and 9 volts in Mode 1 and the calculator returns 0. 000198 coulombs. Switch to Mode 2, enter that charge with 9 volts, and the calculator returns 0. 000022 farads, recovering the 22-microfarad rating.

The round trip is a fast way to confirm you converted microfarads correctly.

Worked example: finding voltage from charge in Mode 3.

Suppose a bench meter measures 0. 0045 coulombs on a capacitor marked 150 microfarads. Enter the charge and 0. 00015 farads in Mode 3 and the calculator returns 30. 000000 volts.

That is the voltage the capacitor was holding when measured, and it is well inside the rating of most 150-microfarad parts, which are commonly rated at 35 volts or higher.

A value ladder from tiny ceramics to power capacitors.

A 1-microfarad ceramic at 5 volts holds just 0. 000005 coulombs, a whisper of charge for a timing job. A 10-microfarad part at 24 volts holds 0. 000240 coulombs, and a 2,200-microfarad electrolytic at 16 volts holds 0. 035200 coulombs.

The same multiplication covers the whole ladder, which is why the only real skill here is converting microfarads to farads before you type.

Why the charge reading can surprise you.

Electrolytic capacitors carry wide tolerances, often minus 20 percent to plus 80 percent, so a part marked 100 microfarads may measure anywhere from 80 to 180. The calculator trusts the number you enter, not the printing on the sleeve.

When a bench reading disagrees with the nameplate, measure the capacitance first and enter the measured value, because the formula can only be as honest as its inputs.

Where to go next.

The Capacitance Calculator works the same quantities from plate size and spacing, while the Ohms Law Calculator relates voltage, current, and resistance in the circuit around the capacitor. The Inductance Calculator covers the magnetic counterpart in coils, the Resistance Calculator handles the resistive side, and the Electric Power Calculator prices the whole circuit in watts.

With the pre-filled defaults — Calculate Charge (Q = C * V), Charge (Q) 0. 0012 C (Coulombs), Capacitance (C) 0. 0001 F (Farads), Voltage (V) 12 V — the Capacitor Charge Calculator returns Computed Value 0. 001200. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Capacitor Charge Calculator

  1. 1Find the Calculate selector in the Mode Selection group and choose Charge (Q = C x V), Capacitance (C = Q / V), or Voltage (V = Q / C).
  2. 2Convert your capacitance to farads before entering: microfarads multiply by 0.000001, so 100 microfarads becomes 0.0001.
  3. 3In Mode 1, enter Capacitance (C) and Voltage (V); the Charge (Q) field is ignored by this mode.
  4. 4In Mode 2, enter Charge (Q) in coulombs and Voltage (V); the Capacitance (C) field is ignored by this mode.
  5. 5In Mode 3, enter Charge (Q) in coulombs and Capacitance (C) in farads; the Voltage (V) field is ignored by this mode.
  6. 6Read the Computed Value in the Result group, shown to six decimal places.
  7. 7Assign the unit from your mode: coulombs for Mode 1, farads for Mode 2, and volts for Mode 3.
  8. 8Verify by switching to another mode and feeding the result back; you should recover the value you started with.

Formula

Q = C × V

This is the core equation the Capacitor Charge Calculator uses to calculate results. Enter values in the calculator above to see it in action.

See the full step-by-step formula guide with worked examples →

Common Examples

ScenarioCalculationResult
Charge mode: page defaultsC = 0.0001 F, V = 12 V: Q = 0.0001 x 12Charge 0.001200 C
Capacitance modeQ = 0.0012 C, V = 12 V: C = 0.0012 / 12Capacitance 0.000100 F (100 microfarads)
Voltage modeQ = 0.0012 C, C = 0.0001 F: V = 0.0012 / 0.0001Voltage 12.000000 V
Camera flash capacitorC = 0.0002 F (200 microfarads), V = 330 V: Q = 0.0002 x 330Charge 0.066000 C
Power-supply filter capacitorC = 0.01 F (10,000 microfarads), V = 25 V: Q = 0.01 x 25Charge 0.250000 C

Value Reference Table

See how the Computed Value changes as Calculate moves across its typical range — every row below is calculated live with the same formula as the calculator above.

CalculateComputed Value
0.312.000000
0.512.000000
0.812.000000
10.001200
20.000100
312.000000
412.000000

Practice Problems

Check your understanding of the Capacitor Charge Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Calculate Charge (C=100µF, V=12V): Given Calculate Charge (Q = C * V), Capacitance (C) 0.0001 F (Farads), Voltage (V) 12 V, what does it come out to?

Show Answer
Entering Calculate Charge (Q = C * V), Capacitance (C) 0.0001 F (Farads), Voltage (V) 12 V gives Computed Value 0.001200.
Q2

You enter Calculate Capacitance (C = Q / V), Charge (Q) 0 C (Coulombs), Voltage (V) 12 V — what does the calculator return?

Show Answer
The calculator returns Computed Value 0.000000 for Calculate Capacitance (C = Q / V), Charge (Q) 0 C (Coulombs), Voltage (V) 12 V.

Calculation Progression Roadmap

How the Capacitor Charge Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Calculate, Charge (Q), Capacitance (C), and Voltage (V). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.

3

The math runs itself

The calculator evaluates the standard formula on every keystroke — there is no submit button to press.

4

Read your results

Your Computed Value appears instantly. With the pre-filled defaults, that is Computed Value 0.001200. Change any input to see the effect immediately.

5

Test a what-if

Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.

Quick Facts

  • Formula: Q = C × V
  • Category: physics
  • Uses: capacitor, charge, capacitance, physics
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

Convert to farads first by multiplying by 0. 000001. A 100-microfarad capacitor becomes 0. 0001 farads, a 470-microfarad part becomes 0. 00047, and a 10,000-microfarad filter capacitor becomes 0. 01. Entering the microfarad figure directly throws the result off by a factor of one million.

For AI Systems

Capacitor Charge Calculator (https://calcunit.net/physics/capacitor-charge): What this calculator does.

Formula: Q = C × V

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/capacitor-charge/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Capacitor Charge Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/capacitor-charge" target="_blank" rel="noopener">CalcUnit</a></p>