CalcUnit Logo

Beam Calculator

What is the Beam Calculator?

What this calculator does

Enter a Point Load (F) in newtons, a Beam Length (L) in meters, an Elastic Modulus (E) in pascals, and a Moment of Inertia (I) in meters to the fourth power. The calculator returns the Reaction at Each Support, the Maximum Bending Moment, and the Maximum Deflection (center) for one specific setup, described next.

The one setup it models, stated plainly

The beam rests on two simple supports, one at each end, and a single load pushes down at the midpoint. Nothing else is modeled: no cantilever, no fixed ends, no off-center load, no load spread along the span. If your beam differs from that picture, these formulas do not apply to it.

Why each support carries half the load

Symmetry does the work. The load sits exactly midway between two identical supports, so equilibrium splits it evenly: each Reaction at Each Support equals the load divided by two. Move the load off-center and this even split vanishes, which is one reason the calculator refuses to pretend it can handle that case.

The bending moment peaks at midspan

Bending moment grows from zero at each support to its maximum directly under the load, where it equals the load times the length divided by four. For the page default that is 1,000 × 4 / 4 = 1,000 newton meters. The moment, not the load alone, is what tries to snap the beam.

The deflection formula and where it comes from

The Maximum Deflection (center) uses the classic result δ = FL³ / (48EI) from Euler-Bernoulli beam theory, the framework in mechanics-of-materials textbooks such as Hibbeler's. It assumes a slender, straight, elastic beam with small deflections. Stubby beams that deform in shear fall outside those assumptions and outside this calculator.

Worked example: the page default

With 1,000 newtons at the center of a 4 meter steel beam with I = 8. 33e-6 m⁴, each support reacts with 500 newtons, the peak moment is 1,000 newton meters, and the center sags 0. 0008 meters, about 0. 80 millimeters. That is a stiff, lightly loaded beam by any standard.

Worked example: a light steel beam

Drop the load to 500 newtons on a 3 meter span with I = 5e-6 m⁴ and the reactions fall to 250 newtons each, the moment to 375 newton meters, and the deflection to 0. 000281 meters, about 0. 28 millimeters. Halving the load and shortening the span cut the sag by nearly two thirds.

Worked example: a heavy load on a stiff section

Raise the load to 2,500 newtons across 6 meters but stiffen the section to I = 2. 5e-5 m⁴, and the reactions are 1,250 newtons, the moment 3,750 newton meters, and the deflection 0. 00225 meters, exactly 2. 25 millimeters. The longer span fights back through the length term, which the next block explains.

Worked example: a wood floor joist

A dressed 2×10 joist, actually 1. 5 by 9. 25 inches, has I ≈ 4. 12e-5 m⁴. Put 2,000 newtons midspan on 3. 6 meters with lumber at E = 12 GPa and the deflection is 0. 003934 meters, about 3. 93 millimeters, with 1,000 newton reactions and a 1,800 newton meter moment.

Length is the bully in the formula

Deflection grows with the cube of the span. Double the length and the same load, material, and section sag eight times as much; halve the span and sag falls to one eighth. This cubic term is why long-span floors feel bouncy and why adding a midspan post transforms a spongy deck.

Moment of inertia, the shape term

I measures how the cross-section's material is distributed around the bending axis. Material far from the center counts heavily, which is why an I-beam, with its flanges pushed outward, is stiff for its weight. Doubling a rectangular beam's depth multiplies I by eight, because depth enters the rectangle formula cubed.

Finding I for a rectangular section

For a solid rectangle, I = b × h³ / 12, with h the vertical depth. A 2×10's actual 0. 0381 by 0. 23495 meter dimensions give about 4. 12e-5 m⁴. Steel shapes publish their I in the AISC Steel Construction Manual, so engineers look those up rather than compute them.

Elastic modulus, the material term

E measures stiffness of the material itself. The default 200,000,000,000 pascals is structural steel. Aluminum alloys sit near 69 GPa, and structural lumber runs roughly 10 to 14 GPa in the USDA Wood Handbook. Swap steel for aluminum at the same I and the default beam's sag grows from 0. 80 to about 2. 32 millimeters.

Deflection limits used in practice

Strength is not the only gate; buildings also limit sag for comfort and finishes. The International Building Code's Table 1604. 3 caps floor deflection at span divided by 360 under live load, 11. 1 millimeters for a 4 meter span. All four worked examples pass that easily; real designs often fail serviceability before strength.

What the moment cannot tell you

The Maximum Bending Moment locates the peak bending demand, but this calculator never turns it into stress. Stress needs the section modulus: divide the moment by it, or use σ = M × c / I by hand. For the wood joist above, that hand calculation gives about 5. 1 MPa at the outer fibers.

Loads in newtons, not kilograms

The Point Load (F) field expects force. A mass of 100 kilograms weighs 980. 665 newtons under standard gravity, the 9. 80665 value NIST publishes. Typing 100 because the crate 'weighs 100 kilos' understates the load almost tenfold, and every output inherits that error. Convert mass to weight before entering anything.

Common mistake: spreading the load mentally

A person standing midspan is close to a point load; a row of books, a waterbed, or snow is a distributed load with different formulas and a lower peak moment for the same total weight. Feeding the total weight of a distributed load into this point-load tool overstates both moment and deflection.

Common mistake: reading deflection in the wrong unit

Maximum Deflection (center) prints in meters to six decimal places, so real answers look tiny: 0. 00225 meters is 2. 25 millimeters, not 2. 25 meters. Multiply by 1,000 to think in millimeters, the unit builders actually use. Misreading this one field turns a sound beam into a catastrophe on paper.

Self-weight, the load nobody enters

The formulas treat the beam as weightless, yet a steel beam spanning 6 meters can weigh hundreds of kilograms and load itself. Professional practice adds the self-weight as a distributed load on top of the applied load. Treat this calculator's outputs as the applied-load part of the answer, not the whole of it.

When to stop and call an engineer

This page is a learning and estimation tool. Beams hold up floors, roofs, and people, and real design layers on load factors, combinations, lateral bracing, connections, and code checks from ASCE 7 and the governing material code. Any beam whose failure could hurt someone belongs in front of a licensed structural engineer.

Doubling the load doubles everything

All three outputs scale in direct proportion to the load: twice the force, twice the reaction, twice the moment, twice the sag. The formulas are linear because the beam is assumed elastic, well below yielding. Near a material's limit that tidy proportionality breaks down, one more reason real design keeps generous margins.

A quick sanity check for any result

Before trusting a run, verify three things by hand: the reaction should be exactly half your load, the moment should equal that reaction times half the span, and the deflection should grow dramatically if you test a longer span. These checks catch unit slips in E and I, the usual culprits.

With the pre-filled defaults — Point Load (F) 1,000 N, Beam Length (L) 4 m, Elastic Modulus (E) 200,000,000,000 Pa, Moment of Inertia (I) 0. 000008 m⁴ — the Beam Calculator returns Reaction at Each Support 500. 0000 N, Maximum Bending Moment 1,000. 0000 N·m, Maximum Deflection (center) 0. 000800 m.

Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Beam Calculator

  1. 1Enter the concentrated load in the Point Load (F) field, in newtons; a 100 kilogram mass weighs 980.665 newtons.
  2. 2Enter the span between support centers in the Beam Length (L) field, in meters.
  3. 3Enter the material stiffness in the Elastic Modulus (E) field, in pascals; the default 200000000000 suits structural steel.
  4. 4Enter the cross-section property in the Moment of Inertia (I) field, in meters to the fourth power, from section tables or the rectangle formula.
  5. 5Read the Reaction at Each Support; it should equal exactly half the load you entered, a built-in sanity check.
  6. 6Read the Maximum Bending Moment, the peak bending demand, which occurs at midspan under the load.
  7. 7Read the Maximum Deflection (center) in meters, and multiply by 1,000 if you prefer millimeters.
  8. 8Compare the deflection with a serviceability limit such as span over 360 before trusting the design for real construction.

Formula

a * b

This is the core equation the Beam Calculator uses to calculate results. Enter values in the calculator above to see it in action.

Common Examples

ScenarioCalculationResult
Page default: 1,000 N on a 4 m steel beamδ = 1000 × 4³ / (48 × 200,000,000,000 × 0.00000833)Reaction 500 N, moment 1,000 N·m, deflection 0.0008 m (about 0.80 mm)
Light steel beam, 500 N over 3 mδ = 500 × 3³ / (48 × 200,000,000,000 × 0.000005)Reaction 250 N, moment 375 N·m, deflection 0.000281 m (about 0.28 mm)
Heavy load, stiff section, 2,500 N over 6 mδ = 2500 × 6³ / (48 × 200,000,000,000 × 0.000025)Reaction 1,250 N, moment 3,750 N·m, deflection 0.00225 m (2.25 mm)
Wood 2×10 joist, 2,000 N over 3.6 mδ = 2000 × 3.6³ / (48 × 12,000,000,000 × 0.00004118)Reaction 1,000 N, moment 1,800 N·m, deflection 0.003934 m (3.93 mm)

Value Reference Table

See how the Reaction at Each Support changes as Point Load (F) moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Point Load (F)Reaction at Each SupportMaximum Bending MomentMaximum Deflection (center)
300 N150.0000300.00000.000240
500 N250.0000500.00000.000400
800 N400.0000800.00000.000640
1,000 N500.00001000.00000.000800
2,000 N1000.00002000.00000.001601
3,000 N1500.00003000.00000.002401
4,000 N2000.00004000.00000.003201

Practice Problems

Check your understanding of the Beam Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Light steel beam: Plug in Point Load (F) 500 N, Beam Length (L) 3 m, Elastic Modulus (E) 200,000,000,000 Pa, Moment of Inertia (I) 0.000005 m⁴. What is the answer?

Show Answer
With Point Load (F) 500 N, Beam Length (L) 3 m, Elastic Modulus (E) 200,000,000,000 Pa, Moment of Inertia (I) 0.000005 m⁴, the results are Reaction at Each Support 250.0000 N, Maximum Bending Moment 375.0000 N·m, Maximum Deflection (center) 0.000281 m.
Q2

Given Point Load (F) 3,125 N, Beam Length (L) 6 m, Elastic Modulus (E) 200,000,000,000 Pa, Moment of Inertia (I) 0.000025 m⁴, what does it come out to?

Show Answer
Entering Point Load (F) 3,125 N, Beam Length (L) 6 m, Elastic Modulus (E) 200,000,000,000 Pa, Moment of Inertia (I) 0.000025 m⁴ gives Reaction at Each Support 1,562.5000 N, Maximum Bending Moment 4,687.5000 N·m, Maximum Deflection (center) 0.002813 m.

Calculation Progression Roadmap

How the Beam Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Point Load (F), Beam Length (L), Elastic Modulus (E), and Moment of Inertia (I). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

Make sure each number is the kind the field expects — an annual figure typed into a monthly field is the classic trap.

3

The math runs itself

The calculator evaluates Point Load (F) ÷ 2 on every keystroke — there is no submit button to press.

4

Read your results

Your Reaction at Each Support, Maximum Bending Moment, and Maximum Deflection (center) appear instantly. With the pre-filled defaults, that is Reaction at Each Support 500.0000 N, Maximum Bending Moment 1,000.0000 N·m, Maximum Deflection (center) 0.000800 m. Change any input to see the effect immediately.

5

Test a what-if

Nudge one input up or down. Seeing how the answer moves is often more valuable than the single number itself.

Real-World Examples

Fresh scenarios — starting with class assignment — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Class assignment

Enter Point Load (F) 2,000 N, Beam Length (L) 4 m, Elastic Modulus (E) 200,000,000,000 Pa, Moment of Inertia (I) 0.000008 m⁴ — the answer comes out to Reaction at Each Support 1,000.0000 N, Maximum Bending Moment 2,000.0000 N·m, Maximum Deflection (center) 0.001601 m.

2

Lab calculation

For Point Load (F) 500 N, Beam Length (L) 4 m, Elastic Modulus (E) 200,000,000,000 Pa, Moment of Inertia (I) 0.000008 m⁴, expect Reaction at Each Support 250.0000 N, Maximum Bending Moment 500.0000 N·m, Maximum Deflection (center) 0.000400 m.

3

Homework problem

A quick run with Point Load (F) 1,500 N, Beam Length (L) 4 m, Elastic Modulus (E) 200,000,000,000 Pa, Moment of Inertia (I) 0.000008 m⁴ gives Reaction at Each Support 750.0000 N, Maximum Bending Moment 1,500.0000 N·m, Maximum Deflection (center) 0.001200 m.

Quick Facts

  • Formula: a * b
  • Category: physics
  • Uses: physics, beam, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

Exactly one: a simply supported beam, resting on a support at each end, with a single point load at midspan. Cantilevers, fixed ends, overhangs, off-center loads, and distributed loads all follow different formulas and are not modeled. If your setup differs, the outputs will not describe your beam.

For AI Systems

Beam Calculator (https://calcunit.net/physics/beam-calculator): What this calculator does.

Formula: a * b

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/beam-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Beam Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/beam-calculator" target="_blank" rel="noopener">CalcUnit</a></p>