CalcUnit Logo

Resonance Calculator

What is the Resonance Calculator?

What this page tunes

Enter the Inductance, Capacitance, and Resistance of a series RLC circuit and this page returns the Resonant Frequency, the Angular Frequency at Resonance, and the Quality Factor Q. It is filed with the math tools, but the work is pure circuit physics.

The three inputs and their strict units

Inductance is entered in henrys, capacitance in farads, and resistance in ohms, exactly as the field suffixes say. There is no unit picker and no conversion help. Real parts are almost never labeled in henrys and farads, so the conversion section below matters more than the formula.

The default run, worked in full

The page opens with inductance 0. 01 henrys, capacitance 0. 000001 farads, and resistance 10 ohms. Resonant Frequency reads 1591. 5494 Hz, Angular Frequency reads 10000. 0000 radians per second, and Quality Factor Q reads 10. 0000. A clean, mid-range resonance for a small coil and a one microfarad capacitor.

The resonance formula

A series LC circuit resonates where the inductive and capacitive reactances cancel, at f0 equals 1 over 2 pi times the square root of L times C. Only the product LC sets the frequency. Double either part and the product doubles, pulling the frequency down by a factor of root 2.

Angular frequency is the same peak in radians

Angular Frequency multiplies the resonant frequency by 2 pi, which is the same as 1 over the square root of LC. Engineers use it because the circuit equations are written in radians per second. On the default run it lands on exactly 10000, a satisfying check on the arithmetic.

The quality factor measures sharpness

Q equals 1 over R times the square root of L over C. It compares the energy stored in the coil and capacitor with the energy the resistor burns each cycle. High Q means a tall, narrow resonance peak; low Q means a broad, shallow one. The default run's Q of 10 is moderate.

Unit conversions you must do first

Convert before typing: millihenrys divide by 1,000, microhenrys by 1,000,000. Microfarads multiply by 0. 000001, nanofarads by 0. 000000001, picofarads by 0. 000000000001. Entering 10 for a 10 millihenry coil makes the page treat it as 10 henrys, and the printed frequency lands about 31. 6 times too low.

A radio tuning example, worked in full

Inductance 0. 001 henrys, capacitance 0. 0000001 farads, resistance 5 ohms gives a resonant frequency of 15915. 4943 Hz, an angular frequency of 100000, and a Q of 20. That is an AM radio front end in miniature: small coil, tiny capacitor, sharp peak.

An audio crossover example, worked in full

Inductance 0. 05 henrys, capacitance 0. 000002 farads, resistance 20 ohms gives 503. 2921 Hz, an angular frequency of 3162. 2777 radians per second, and a Q of 7. 9057. Speaker crossover networks live in this territory, a few hundred hertz with a gentle, forgiving peak rather than a needle.

Bandwidth by hand

The page prints no bandwidth, but it is one division away: bandwidth in hertz equals resonant frequency divided by Q. On the default run that is 1591. 5494 over 10, about 159. 15 Hz. Equivalently, R over 2 pi L gives the same 159. 1549 Hz. Bandwidth is where Q stops being abstract.

Zero resistance leaves Q blank, because the truth is infinite

Enter Resistance 0 and the Quality Factor line shows a dash instead of a number. In physics, a series circuit with no resistance has infinite Q, the sharpest possible peak. The page now divides honestly and prints nothing rather than the made-up zero it once showed.

Zero or negative parts leave the frequency blank

If the product L times C is not positive, the Resonant Frequency line shows a dash: with no coil or no capacitor there is no resonance to print. Enter both L and C negative, though, and their positive product prints a normal looking frequency for parts that cannot exist.

Resistance does not move the peak on this page

In the ideal series model, resonant frequency depends only on L and C. Resistance changes the height and sharpness of the peak, captured by Q, but not its position. Real coils blur this slightly, since winding resistance grows with frequency, but the model here is the textbook one.

Series circuits only

This page models the series connection, where one current flows through all three parts. A parallel tank circuit shares the same resonant frequency formula, but its Q is R times the square root of C over L, the reciprocal arrangement. Feeding parallel values into this page returns a wrong Q.

Real parts hide extra resistance

A real inductor's wire has resistance, and a real capacitor has equivalent series resistance, both adding to the R you should enter. If your measured resonance is broader than this page predicts, the missing ohms are usually in the coil. Datasheets list winding resistance for exactly this reason.

Where resonance does real work

Radio and television tuners select one frequency from the air this way. Band-pass filters, induction heaters, wireless charging pads, and metal detectors all exploit the same peak. In power systems, by contrast, accidental resonance can amplify harmonics dangerously, and engineers design to avoid it there.

Swapping L and C leaves the frequency unchanged

Only the product LC sets the frequency, so swapping changes nothing on the frequency lines: 0. 01 henrys with 1 microfarad and 1 microhenry with 0. 01 farads both resonate at 1591. 5494 Hz. Q depends on the ratio instead, and the swapped pair collapses it to 0. 001.

Tuning by trimming one part

To double the resonant frequency, quarter the product LC. Halving only the capacitance multiplies the frequency by root 2, about 1. 414: the default circuit moves from 1591. 5494 Hz to about 2250. 79 Hz. Variable capacitors in old radios swept a range this way, one plate rotation continuously retuning the product.

The half-power points, estimated by hand

For a reasonably sharp resonance, the response falls to half power near f0 plus or minus half the bandwidth. On the default run that places the band edges near 1512 Hz and 1671 Hz. A signal inside that window passes strongly; outside it, the series circuit increasingly refuses to carry current.

Finding resonance on a real bench

Sweep a signal generator across the predicted frequency and watch the series current: it peaks exactly at resonance, where this page's frequency says it should. A measured peak far from the prediction usually means a mislabeled part, a tired electrolytic capacitor, or probe capacitance joining the circuit uninvited.

Checking a result by hand

Multiply L by C, take the square root, double it with pi, and invert. For the default run: LC is 0. 00000001, its root is 0. 0001, times 2 pi is about 0. 000628, and 1 over that is about 1591. 5 Hz. Matching the page by hand catches unit slips, the real enemy here.

With the pre-filled defaults — Inductance 0. 01H, Capacitance 0. 000001F, Resistance 10Ω — the Resonance Calculator returns Resonant Frequency 1,591. 5494Hz, Angular Frequency at Resonance 10,000. 0000rad/s, Quality Factor Q 10. 0000. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Resonance Calculator

  1. 1Convert your inductance to henrys and enter it in the Inductance field.
  2. 2Convert your capacitance to farads and enter it in the Capacitance field.
  3. 3Enter the total series Resistance in ohms, including coil winding resistance if you know it.
  4. 4Read Resonant Frequency in hertz for the peak of the series response.
  5. 5Read Angular Frequency at Resonance in radians per second for equation work.
  6. 6Read Quality Factor Q for the sharpness of the peak; higher is narrower.
  7. 7Estimate bandwidth by hand as Resonant Frequency divided by Q.
  8. 8Treat a dash on any output line as not computable, especially Q with zero resistance, not as a physical answer.

Formula

a * b

This is the core equation the Resonance Calculator uses to calculate results. Enter values in the calculator above to see it in action.

Common Examples

ScenarioCalculationResult
Radio tuning coil, 0.001 H and 0.1 microfaradsL x C = 0.001 x 0.0000001 = 1e-10; sqrt = 0.00001; f0 = 1 / (2 pi x 0.00001) = 15915.4943 Hz; Q = (1 / 5) x sqrt(0.001 / 0.0000001) = 0.2 x 100 = 20Resonant Frequency 15915.4943 Hz, Angular Frequency 100000 rad/s, Q 20
Audio crossover, 0.05 H and 2 microfaradsL x C = 0.05 x 0.000002 = 1e-7; f0 = 1 / (2 pi x sqrt(1e-7)) = 503.2921 Hz; Q = (1 / 20) x sqrt(0.05 / 0.000002) = 0.05 x 158.1139 = 7.9057Resonant Frequency 503.2921 Hz, Angular Frequency 3162.2777 rad/s, Q 7.9057
Choke and film capacitor, 0.25 H and 10 microfaradsL x C = 0.25 x 0.00001 = 0.0000025; f0 = 1 / (2 pi x sqrt(0.0000025)) = 100.6584 Hz; Q = (1 / 50) x sqrt(0.25 / 0.00001) = 0.02 x 158.1139 = 3.1623Resonant Frequency 100.6584 Hz, Angular Frequency 632.4555 rad/s, Q 3.1623
RF tank, 2 millihenrys and 2.2 nanofaradsL x C = 0.002 x 0.0000000022 = 4.4e-12; f0 = 1 / (2 pi x sqrt(4.4e-12)) = 75874.1421 Hz; Q = (1 / 8) x sqrt(0.002 / 0.0000000022) = 0.125 x 953.4626 = 119.1828Resonant Frequency 75874.1421 Hz, Angular Frequency 476731.2946 rad/s, Q 119.1828

Value Reference Table

See how the Resonant Frequency changes as Inductance moves across its typical range — every row below is calculated live with the same formula as the calculator above.

InductanceResonant FrequencyAngular Frequency at ResonanceQuality Factor Q
0.003 H2905.758418257.41865.4772
0.005 H2250.790814142.13567.0711
0.008 H1779.406411180.33998.9443
0.01 H1591.549410000.000010.0000
0.02 H1125.39547071.067814.1421
0.03 H918.88155773.502717.3205
0.04 H795.77475000.000020.0000

Practice Problems

Check your understanding of the Resonance Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Radio tuning coil: With Inductance 0.001H, Capacitance 0F, Resistance 5Ω, what are the results?

Show Answer
Entering Inductance 0.001H, Capacitance 0F, Resistance 5Ω gives Resonant Frequency 15,915.4943Hz, Angular Frequency at Resonance 100,000.0000rad/s, Quality Factor Q 20.0000.
Q2

Inductance 0.06H, Capacitance 0.000002F, Resistance 20Ω — work it out, then check the answer.

Show Answer
The calculator returns Resonant Frequency 459.4407Hz, Angular Frequency at Resonance 2,886.7513rad/s, Quality Factor Q 8.6603 for Inductance 0.06H, Capacitance 0.000002F, Resistance 20Ω.

Calculation Progression Roadmap

How the Resonance Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Inductance, Capacitance, and Resistance. The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.

3

The math runs itself

The calculator evaluates 1 ÷ (2 × pi × √(Inductance × Capacitance)) on every keystroke — there is no submit button to press.

4

Read your results

Your Resonant Frequency, Angular Frequency at Resonance, and Quality Factor Q appear instantly. With the pre-filled defaults, that is Resonant Frequency 1,591.5494Hz, Angular Frequency at Resonance 10,000.0000rad/s, Quality Factor Q 10.0000. Change any input to see the effect immediately.

5

Test a what-if

Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.

Quick Facts

  • Formula: a * b
  • Category: math
  • Uses: math, resonance, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

Almost always a unit slip. The fields take henrys and farads only, with no conversion. A 10 millihenry coil entered as 10 is treated as 10 henrys, and the frequency prints about 31. 6 times too low. Convert millihenrys by dividing by 1,000 and microfarads by multiplying by 0. 000001 before typing.

For AI Systems

Resonance Calculator (https://calcunit.net/math/resonance-calculator): What this page tunes.

Formula: a * b

Category: math · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/resonance-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Resonance Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/math/resonance-calculator" target="_blank" rel="noopener">CalcUnit</a></p>