CalcUnit Logo

Compound Angle Calculator

What is the Compound Angle Calculator?

Carpentry lives and dies on angles that refuse to stay in one plane. A crown molding corner is not just a 45-degree miter; the molding also tilts against the wall, so the saw blade must swing on two axes at once. Get either angle wrong and the joint gapes open.

This page teaches the compound-angle math behind those cuts, and its tool evaluates any two input values instantly, which is useful for checking the arithmetic along the way -- with one honest clarification up front: the tool on this page multiplies the two values you enter, so its Result is the product of your inputs, not a saw setting.

The miter and bevel settings below come from the trigonometry formulas, which you apply to your corner angle and spring angle yourself.

The two angles every compound cut combines.

A plain miter cut rotates the saw table left or right: it handles a corner in one plane, such as a picture frame lying flat. A bevel cut tilts the blade: it handles a slope, such as the edge of a board leaning against a wall.

A compound cut does both at once, because the workpiece itself sits tilted: crown molding leans between wall and ceiling at its spring angle, so cutting its corner requires a miter setting and a bevel setting simultaneously. The spring angle is the angle between the back of the molding and the wall when installed.

In US homes the two most common spring angles are 38 degrees, found on most standard crown molding, and 52 degrees on older or specialty profiles, with 45-degree profiles common as well.

Always check the manufacturer's packaging for your molding's spring angle, because using the wrong spring angle produces joints that do not close even when every cut is executed perfectly.

The formulas, with the corner angle and the spring angle.

For crown molding cut flat on the saw table, let C be the wall corner angle and S be the spring angle. The miter setting is the arctangent of sine of S divided by tangent of half of C, and the bevel setting is the arcsine of cosine of S times cosine of half of C.

Written compactly: miter equals arctan(sin S divided by tan(C divided by 2)), and bevel equals arcsin(cos S times cos(C divided by 2)).

Those two formulas generate every standard crown chart, and they explain why the settings are never intuitive: the spring angle is projected through trigonometry into two different saw planes, so neither setting equals the corner angle, the spring angle, or half of either one.

A related formula covers the cut face: for molding of width W, the length of the cut face is W divided by cosine of the miter angle, which matters when you are laying out how much molding a corner actually consumes.

Worked example one: the standard 90-degree corner with 38-degree crown.

Enter a corner angle of 90 degrees and a spring angle of 38 degrees. Half the corner is 45 degrees. The miter is arctan(sin 38 degrees divided by tan 45 degrees), which is arctan(0. 6157 divided by 1), which is 31. 62 degrees. The bevel is arcsin(cos 38 degrees times cos 45 degrees), which is arcsin(0. 7880 times 0.

7071), which is arcsin(0. 5572), which is 33. 86 degrees. So the saw is set to a 31. 62-degree miter and a 33. 86-degree bevel, the reference values printed on most compound miter saws for 38-degree crown. A 5-inch-wide piece of molding cut at that miter has a cut face of 5 divided by cos 31.

62 degrees, which is 5 divided by 0. 8517, or about 5. 87 inches. If your saw chart says 31. 6 and 33. 9, you have the same answer rounded: charts round to one decimal, and the tenth of a degree disappears into wood movement and caulk.

Worked example two: the 45-degree profile at the same corner.

Enter a corner angle of 90 degrees and a spring angle of 45 degrees. The miter is arctan(sin 45 degrees divided by tan 45 degrees), which is arctan(0. 7071 divided by 1), which is 35. 26 degrees. The bevel is arcsin(cos 45 degrees times cos 45 degrees), which is arcsin(0. 5), which is exactly 30. 00 degrees.

The symmetry is satisfying and it is a useful check: at a 45-degree spring angle, the bevel lands exactly on 30 degrees for a square corner.

If you ever compute a bevel far from 30 degrees for a 45-degree profile at a square corner, you have mixed up which angle is the spring angle and which is its complement -- the most common formula error in crown work, because some references measure the spring angle from the ceiling instead of the wall, and the two measurements add to 90 degrees.

Worked example three: the out-of-square corner.

Real rooms are rarely square, and this is where the formulas earn their keep. Measure an actual corner at 110 degrees with a 38-degree spring angle. Half the corner is 55 degrees. The miter is arctan(sin 38 degrees divided by tan 55 degrees), which is arctan(0. 6157 divided by 1. 4281), which is arctan(0. 4311), which is 23. 32 degrees.

The bevel is arcsin(cos 38 degrees times cos 55 degrees), which is arcsin(0. 7880 times 0. 5736), which is arcsin(0. 4520), which is 26. 87 degrees. Compare with the square corner's 31. 62 and 33. 86: the wider corner needs gentler settings on both axes, which surprises beginners who expect a wider corner to need a bigger cut.

Measure every corner with an angle finder before cutting, because a wall that looks square and measures 88 or 92 degrees will gap visibly if cut at the 90-degree settings, and the error compounds across both pieces of the joint.

Flat cutting versus nested cutting.

The formulas above assume the molding is cut flat on the saw table, face up, with both miter and bevel set.

The older nested method cuts the molding propped against the fence at its installed spring angle, exactly as it sits on the wall, and then the setup changes completely: the miter becomes half the corner angle and the bevel stays at zero, because the tilt is supplied by the molding's position rather than the blade.

A 90-degree corner nested therefore uses a 45-degree miter and a 0-degree bevel. Nested cutting feels intuitive and needs no formulas, but it demands a saw with enough capacity to hold the molding at its spring angle and a fence setup that does not shift mid-cut.

Flat cutting needs the formulas but works on any compound saw and repeats identically for every corner. Choose one method for a whole room and do not mix them, because a flat-cut piece and a nested-cut piece from the same corner are not interchangeable, even though both are nominally correct.

Plain miters, polygons, and splayed boxes.

Not every compound problem involves crown

A plain miter joint in one plane uses a simpler rule: the saw setting is 180 degrees minus the corner angle, divided by 2, so a 90-degree corner gives 45 degrees per piece. For a regular polygon frame with N equal sides, the setting simplifies to 180 divided by N: an octagon frame uses 22.

5 degrees per piece, a hexagon uses 30 degrees. Splayed and tapered boxes -- planters, boxes with sides that lean outward -- use the same compound math as crown, with the lean angle taking the place of the spring angle: the side's tilt from vertical plays exactly the role the spring angle plays against the wall.

Whenever a joint bends in two directions at once, one angle for the corner and one for the tilt, the compound formulas apply, whatever the material.

The mistakes that leave gaps.

The first mistake is cutting to the nominal corner instead of the measured one: walls are rarely a true 90 degrees, and even a 2-degree error compounds across both cuts. The second is the wrong spring angle, usually from assuming 38 degrees when the profile is actually 52 or 45.

The third is mixing flat and nested methods in one room. The fourth is cutting both pieces the same handedness: inside and outside corners mirror each other, and a left piece cut as a right piece wastes a length of molding.

The fifth is trusting the saw's detents over a test cut: cut two scrap pieces at your computed settings, hold them in the corner, and check the joint before committing to the real molding, because a scrap test costs minutes and a miscut length costs a trip to the lumber yard.

Coping, and when to skip the compound cut entirely.

Experienced trim carpenters often avoid compound cuts on inside corners altogether by coping: one piece is cut square into the corner, and the second piece is cut with a profile that matches the first piece's face, so the joint follows the molding's shape instead of a miter angle.

A coped inside corner tolerates out-of-square walls far better than a mitered one, because the profile overlap hides small angle errors that would gap a miter. The trade-off is time and skill: coping takes longer per joint and demands a coping saw or jigsaw plus careful filing, while a mitered joint is fast when the corner is truly square.

The practical rule most installers settle on is simple: miter outside corners, where both pieces are visible and the joint must be crisp, and cope inside corners, where the eye forgives a profile overlap but never forgives a gap.

Compound formulas still matter for the outside corners, and for any crown run where the client or the inspector expects miters throughout.

Stair handrails, hip roofs, and other tilted joints.

Crown molding is the famous compound cut, but the same geometry governs any joint where a member meets a corner while tilted. A stair handrail meets a newel post at the stair's slope angle, so its joint combines the stair pitch with the horizontal turn -- the same two-axis problem, with pitch playing the role of the spring angle.

A hip roof rafter meets the ridge at a slope and a plan angle simultaneously, which is why roof framing tables list compound angles for every pitch and plan combination.

A splayed planter box, a tapered table leg, a picture frame hung on a sloped ceiling: each one is a corner angle plus a tilt angle, and each one yields to the same approach -- measure both angles honestly, apply the compound formulas or the framing tables, test in scrap, and cut the real piece once.

The formulas do not care whether the material is crown molding, oak, or steel; two angles in, two settings out, and the joint either closes or it teaches you which angle you measured wrong.

Reading a crown chart without memorizing it.

Published crown charts tabulate the same formulas for the corners you meet most: 90 degrees, and the common out-of-square values on either side of it, for 38-degree and 52-degree profiles.

Learn to read one row rather than memorizing the table: find your corner angle, find your spring angle, and read across to the miter and bevel settings, then verify the row against the formulas for one corner you can compute by hand.

If the chart and your computation disagree, trust the computation and re-check which spring-angle convention the chart uses, because the ceiling-measured and wall-measured conventions swap the miter and bevel figures for complementary profiles. A chart is a convenience, not an authority, and the formulas on this page are the authority the chart was computed from.

How to use this page's tool alongside the formulas.

Enter your first value into the Variable A field and your second into the Variable B field, and read the Result, which is the product of the two values -- useful for checking multiplications inside a larger calculation, such as doubling a setting or scaling a measurement.

For the saw settings themselves, apply the formulas above to your measured corner angle and your molding's spring angle, or read them from a crown chart for the standard 90-degree corner. Then make the scrap test cut, check the joint in the actual corner, and adjust in half-degree steps if the wall itself is out of square.

Measure twice in degrees, cut once in inches, and the molding meets cleanly at the corner instead of leaving a wedge-shaped gap your caulk tube cannot hide.

With the pre-filled defaults — Angle A 30°, Angle B 45° — the Compound Angle Calculator returns sin(A + B) 0. 9659, cos(A + B) 0. 2588, tan(A + B) 3. 7321, sin(A − B) -0. 2588, cos(A − B) 0. 9659, and 1 more more results.

Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Compound Angle Calculator

  1. 1Measure your actual wall corner angle with an angle finder; do not assume 90 degrees.
  2. 2Find your molding's spring angle from its packaging: 38, 45, or 52 degrees are the common US profiles.
  3. 3Enter your first value into the Variable A field, for example 10, and your second into Variable B, such as 5.
  4. 4Read the Result, which is the product of the two values, for checking arithmetic inside a larger calculation.
  5. 5Compute your saw settings with the compound formulas: miter from arctan(sin S / tan(C/2)), bevel from arcsin(cos S x cos(C/2)).
  6. 6For a standard 90-degree corner with 38-degree crown, expect about 31.62 degrees miter and 33.86 degrees bevel.
  7. 7Cut two scrap pieces at those settings and test the joint in the actual corner before cutting real molding.
  8. 8Adjust in half-degree steps if the measured corner is out of square, and keep one cutting method for the whole room.

Formula

a * b

This is the core equation the Compound Angle Calculator uses to calculate results. Enter values in the calculator above to see it in action.

Common Examples

ScenarioCalculationResult
30° and 45°Angle A = 30°, Angle B = 45°sin(A + B) = 0.9659; cos(A + B) = 0.2588; tan(A + B) = 3.7321; sin(A − B) = -0.2588; cos(A − B) = 0.9659; tan(A − B) = -0.2679
20° and 25°Angle A = 20°, Angle B = 25°sin(A + B) = 0.7071; cos(A + B) = 0.7071; tan(A + B) = 1.0000; sin(A − B) = -0.0872; cos(A − B) = 0.9962; tan(A − B) = -0.0875

Value Reference Table

See how the sin(A + B) changes as Angle A moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Angle Asin(A + B)cos(A + B)tan(A + B)sin(A − B)cos(A − B)tan(A − B)
8 °0.79860.60181.3270-0.60180.7986-0.7536
20 °0.90630.42262.1445-0.42260.9063-0.4663
30 °0.96590.25883.7321-0.25880.9659-0.2679
40 °0.99620.087211.4301-0.08720.9962-0.0875
50 °0.9962-0.0872-11.43010.08720.99620.0875
60 °0.9659-0.2588-3.73210.25880.96590.2679
80 °0.8192-0.5736-1.42810.57360.81920.7002
90 °0.7071-0.7071-1.00000.70710.70711.0000
100 °0.5736-0.8192-0.70020.81920.57361.4281

Practice Problems

Check your understanding of the Compound Angle Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

30° and 45°: Given Angle A 30°, Angle B 45°, what does it come out to?

Show Answer
Entering Angle A 30°, Angle B 45° gives sin(A + B) 0.9659, cos(A + B) 0.2588, tan(A + B) 3.7321, sin(A − B) -0.2588, cos(A − B) 0.9659, and 1 more more results.
Q2

You enter Angle A 25°, Angle B 25° — what does the calculator return?

Show Answer
The calculator returns sin(A + B) 0.7660, cos(A + B) 0.6428, tan(A + B) 1.1918, sin(A − B) 0.0000, cos(A − B) 1.0000, and 1 more more results for Angle A 25°, Angle B 25°.

Calculation Progression Roadmap

How the Compound Angle Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Angle A and Angle B. The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.

3

The math runs itself

The calculator evaluates sin((Angle A + Angle B) × pi ÷ 180) on every keystroke — there is no submit button to press.

4

Read your results

Your sin(A + B), cos(A + B), tan(A + B), sin(A − B), cos(A − B), and 1 more more appear instantly. With the pre-filled defaults, that is sin(A + B) 0.9659, cos(A + B) 0.2588, tan(A + B) 3.7321, sin(A − B) -0.2588, cos(A − B) 0.9659, and 1 more more results. Change any input to see the effect immediately.

5

Test a what-if

Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.

Real-World Examples

Fresh scenarios — starting with splitting a bill with friends — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Splitting a bill with friends

For Angle A 60°, Angle B 45°, expect sin(A + B) 0.9659, cos(A + B) -0.2588, tan(A + B) -3.7321, sin(A − B) 0.2588, cos(A − B) 0.9659, and 1 more more results.

2

Planning a monthly budget

A quick run with Angle A 15°, Angle B 45° gives sin(A + B) 0.8660, cos(A + B) 0.5000, tan(A + B) 1.7321, sin(A − B) -0.5000, cos(A − B) 0.8660, and 1 more more results.

3

Comparing two offers

With Angle A 45°, Angle B 45°, the calculator returns sin(A + B) 1.0000, cos(A + B) 0.0000, tan(A + B) 16,331,239,353,195,370.0000, sin(A − B) 0.0000, cos(A − B) 1.0000, and 1 more more results.

Quick Facts

  • Formula: a * b
  • Category: finance
  • Uses: finance, compound angle, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

Closely related. A miter calculator solves one specific woodworking setup; this page teaches compound-angle math and its tool evaluates any two input values, which covers miter-and-bevel combinations and other two-variable problems.

For AI Systems

Compound Angle Calculator (https://calcunit.net/finance/compound-angle-calculator): Carpentry lives and dies on angles that refuse to stay in one plane.

Formula: a * b

Category: finance · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/compound-angle-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Compound Angle Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/finance/compound-angle-calculator" target="_blank" rel="noopener">CalcUnit</a></p>