CalcUnit Logo

Technical Atmosphere Converter

What is the Technical Atmosphere Converter?

The atmosphere that is not quite an atmosphere.

Two pressure units share a name and almost nothing else

The standard atmosphere, atm, is a physics constant. The technical atmosphere, at, is an engineering unit built from a kilogram of force on a square centimeter. Confusing them skews every pressure figure by over 3 percent.

What this converter does.

Type a value into the Technical Atmospheres (at) field and four results appear together: Pascals (Pa), Bar, PSI, and Physical Atmospheres (atm). The last pairing is the one most visitors came for, because it settles the at-versus-atm question with a number instead of an argument.

The technical atmosphere, defined exactly.

One technical atmosphere is one kilogram-force per square centimeter, written kgf/cm²

Because the kilogram-force is defined through standard gravity, the value is exact: 1 at equals 98,066. 5 pascals. No measurement, no rounding, a definition you can lean on.

The standard atmosphere, defined differently.

One standard atmosphere, atm, is exactly 101,325 pascals, the internationally agreed value for average sea-level air pressure. It comes from physics, not from a machinist's square centimeter. Two exact definitions, two different sizes, and only about 3. 3 percent between them.

Why the gap matters in practice.

Three percent sounds like trivia until it reaches a boiler rating, a hydraulic accumulator, or a divers' pressure table copied from a European manual. On a 200-at vessel, mistaking at for atm overstates the pressure by roughly 6. 4 atm worth of force. Gauges have burst over smaller misunderstandings.

Worked example one: the unit itself.

Enter 1 in the Technical Atmospheres field

The converter returns 98,066. 5 pascals, 0. 980665 bar, 14. 2233 PSI, and 0. 967841 atm. Read the last figure slowly: one technical atmosphere is only about ninety-seven hundredths of a standard one. That is the whole page in a single line.

Worked example two: a modest gauge reading.

Enter 3 at, a plausible reading from an older European pressure gauge

The results are 294,199. 5 pascals, 2. 941995 bar, 42. 67 PSI, and 2. 903523 atm. For an American reader, the PSI line is the one that lands: just under 43 pounds per square inch.

Worked example three: a rounder industrial figure.

Enter 10 at

The converter returns 980,665 pascals, 9. 80665 bar, 142. 2334 PSI, and 9. 67841 atm. Notice the bar figure hovering close to, but never equal to, the input: ten at is not ten bar, and the difference grows with the pressure.

Where Americans actually meet this unit.

Old European and Soviet-era machinery manuals, steam tables, imported pressure gauges, and some Japanese equipment plates mark pressure in at or kgf/cm². If a specification sheet gives a plain number in at and your gauge reads PSI, this page is the translator standing between them.

The bar is a cousin, not a twin.

One bar is exactly 100,000 pascals, so one at is 0. 980665 bar, about 2 percent less. Their closeness causes real errors, because 10 at and 10 bar look interchangeable on a crowded nameplate. They are not; this converter keeps the 0. 980665 factor visible for a reason.

PSI, the home unit.

A technical atmosphere equals 14. 2233 PSI, against 14. 6959 PSI for a standard atmosphere. American tire gauges, shop compressors, and plumbing all speak PSI, so this output is usually the practical endpoint: multiply the at figure by roughly 14. 22 and you are home.

Going the other way.

To turn standard atmospheres into technical ones, divide by 0. 967841, or multiply by about 1. 0332: one atm is 1. 0332 at. This converter runs at-to-everything only, so reverse trips take one division by hand, using the same factors printed in its formula line.

Gauge pressure versus absolute pressure.

Historical European gauges often read in atü, technical atmospheres of overpressure, meaning pressure above the surrounding air. The converter assumes the number you type is the pressure itself. If your source is a gauge reading, remember its zero was the atmosphere of the room, not a vacuum.

Why the unit survives at all.

The technical atmosphere fit the metric workshop beautifully: a kilogram-force and a centimeter are bench-scale quantities, and water ten meters deep presses with almost exactly one at. It faded as the pascal and bar standardized, but a century of manuals, plates, and gauges still speaks it.

A three-percent habit worth building.

Whenever a document says atmosphere, ask which one

If it says at, kgf/cm², or comes from an engineering source, think technical. If it says atm in a physics or chemistry source, think standard. This page exists because that single question, asked early, prevents expensive arithmetic later.

The ten-meter water rule.

Divers and hydraulic engineers once loved this unit because water ten meters deep presses down with almost exactly one technical atmosphere. A depth of 30 meters therefore meant about 3 at of water pressure before anyone reached for a table, an elegance the pascal never matched.

Steam tables and boiler rooms.

Generations of steam tables tabulated pressure in kgf/cm², so a heritage boiler nameplate stating 12 at is stating 12 technical atmospheres, roughly 170. 68 PSI. Restorers of vintage engines convert with this page before firing equipment whose safety margins were written in another century's unit.

Spotting the unit on a nameless gauge.

An unlabeled imported gauge that idles near 1 in open air, or maxes out at a suspiciously round 10, 16, or 25, is probably graduated in at or bar rather than atm. Converting a known reference pressure, such as a tire's specified PSI, through this page identifies the scale quickly.

With the pre-filled defaults — Technical Atmospheres (at) 1 — the Technical Atmosphere Converter returns Pascals (Pa) 98,066. 50, Bar 0. 980665, PSI 14. 2233, Physical Atmospheres (atm) 0. 967841. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Technical Atmosphere Converter

  1. 1Confirm your source value is in technical atmospheres (at), also written kgf/cm², not standard atmospheres (atm).
  2. 2Type the value into the Technical Atmospheres (at) field; the page loads with 1 as a starting example.
  3. 3Read the Pascals (Pa) result for the exact SI figure, 98,066.5 pascals per at.
  4. 4Read the Bar result if your equipment or manual works in bar.
  5. 5Read the PSI result if you are comparing against an American gauge or specification.
  6. 6Read the Physical Atmospheres (atm) result to see the same pressure in standard atmospheres.
  7. 7Try 10 to see the pattern: 980,665 Pa, 9.80665 bar, 142.2334 PSI, and 9.67841 atm.
  8. 8For a reverse trip from atm to at, divide the atm figure by 0.967841 by hand.

Formula

at * 98066.5

This is the core equation the Technical Atmosphere Converter uses to calculate results. Enter values in the calculator above to see it in action.

See the full step-by-step formula guide with worked examples →

Common Examples

ScenarioCalculationResult
The unit itself1 at converted with at x 98,066.598,066.5 Pa (0.980665 bar; 14.2233 PSI; 0.967841 atm)
A modest gauge reading3 at converted with at x 98,066.5294,199.5 Pa (2.941995 bar; 42.67 PSI; 2.903523 atm)
An industrial round number10 at converted with at x 98,066.5980,665 Pa (9.80665 bar; 142.2334 PSI; 9.67841 atm)

Value Reference Table

See how the Pascals (Pa) changes as Technical Atmospheres (at) moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Technical Atmospheres (at)Pascals (Pa)BarPSIPhysical Atmospheres (atm)
0.329419.950.2942004.26700.290352
0.549033.250.4903337.11170.483920
0.878453.200.78453211.37870.774273
198066.500.98066514.22330.967841
2196133.001.96133028.44671.935682
3294199.502.94199542.67002.903523
4392266.003.92266056.89343.871364

Practice Problems

Check your understanding of the Technical Atmosphere Converter with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Example calculation: Plug in Technical Atmospheres (at) 1. What is the answer?

Show Answer
Entering Technical Atmospheres (at) 1 gives Pascals (Pa) 98,066.50, Bar 0.980665, PSI 14.2233, Physical Atmospheres (atm) 0.967841.

Calculation Progression Roadmap

How the Technical Atmosphere Converter turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Technical Atmospheres (at). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.

3

The math runs itself

The calculator evaluates Technical Atmospheres (at) × 98066.5 on every keystroke — there is no submit button to press.

4

Read your results

Your Pascals (Pa), Bar, PSI, and Physical Atmospheres (atm) appear instantly. With the pre-filled defaults, that is Pascals (Pa) 98,066.50, Bar 0.980665, PSI 14.2233, Physical Atmospheres (atm) 0.967841. Change any input to see the effect immediately.

5

Test a what-if

Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.

Real-World Examples

Fresh scenarios — starting with everyday conversions — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Everyday conversions

Enter Technical Atmospheres (at) 2 — the answer comes out to Pascals (Pa) 196,133.00, Bar 1.961330, PSI 28.4467, Physical Atmospheres (atm) 1.935682.

2

Travel planning

For Technical Atmospheres (at) 0.5, expect Pascals (Pa) 49,033.25, Bar 0.490333, PSI 7.1117, Physical Atmospheres (atm) 0.483921.

3

Following a recipe

A quick run with Technical Atmospheres (at) 1.5 gives Pascals (Pa) 147,099.75, Bar 1.470998, PSI 21.3350, Physical Atmospheres (atm) 1.451762.

Quick Facts

  • Formula: at * 98066.5
  • Category: converters
  • Uses: converters, technical atmosphere, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

At is the technical atmosphere, one kilogram-force per square centimeter, exactly 98,066. 5 pascals. Atm is the standard atmosphere, exactly 101,325 pascals. One at is only 0. 967841 atm, so the units differ by about 3. 3 percent, enough to matter in engineering work.

For AI Systems

Technical Atmosphere Converter (https://calcunit.net/converters/technical-atmosphere-converter): The atmosphere that is not quite an atmosphere.

Formula: at * 98066.5

Category: converters · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/technical-atmosphere-converter/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Technical Atmosphere Converter — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/converters/technical-atmosphere-converter" target="_blank" rel="noopener">CalcUnit</a></p>