Illuminance Converter
What is the Illuminance Converter?
What this converter does.
Type a light level into the Lux (lx) field and the page returns it in foot-candles (fc) and phots (ph). Lux is the metric unit lighting designers, photographers, and building engineers calculate in, while foot-candles remain the everyday unit on American drawings and in American codes, so this page bridges the two.
It opens on a standard office light level.
The page loads with 500 lux, a classic target for office work
The outputs read 46. 4515 foot-candles and 0. 050000 phots. That pairing is the most common translation in lighting practice, because American specifications usually round the same office target to about 50 foot-candles on the drawing set.
Lux measures light landing on a surface.
One lux is one lumen of luminous flux spread over one square meter. It describes light arriving at a desk, a page, or a playing field, not light leaving the lamp. NIST treats the lux as the SI unit of illuminance, derived from the lumen and the square meter.
A foot-candle measures the same thing in feet.
One foot-candle is one lumen spread over one square foot, the imperial twin of the lux. The name survives from the era when a standard candle at one foot set the scale. American lighting codes, gymnasium specifications, and older engineering handbooks still state their levels in foot-candles first.
The factor comes from the size of a square foot.
A square foot is exactly 0. 09290304 square meters, so one foot-candle packs its lumen into a smaller area and equals 10. 7639 lux. This converter multiplies lux by 0. 09290304 to get foot-candles. Remembering the rough ten-to-one ratio lets you estimate most conversions in your head before checking here.
Worked example: a living room in the evening.
Enter 150 lux, comfortable residential light for conversation and television
The foot-candle output reads 13. 9355 and the phot output reads 0. 015000. American guidance for living spaces sits near 10 to 20 foot-candles, so this entry lands squarely in the relaxed end of the range.
Worked example: a bright classroom or store.
Enter 1000 lux, the level retail displays and detailed bench work often target. You get 92. 9030 foot-candles and 0. 100000 phots. Jewelry counters and inspection stations live near this brightness because fine detail and color judgment both improve as illuminance climbs toward four figures.
Worked example: an overcast day outdoors.
Enter 10,000 lux, ordinary daylight under a fully clouded sky
The results are 929. 0304 foot-candles and exactly 1. 000000 phot. This is the one clean anchor the phot offers: ten thousand lux makes one phot, which is why the old unit survives mainly as a curiosity at daylight levels.
Worked example: direct summer sunlight.
Enter 100,000 lux, strong midday sun
Foot-candles read 9290. 3040 and phots read 10. 000000. The jump from the office example is two hundredfold, a reminder of how aggressively the human eye adapts: the same visual system handles both scenes and calls each of them normal.
Worked example: the museum limit for fragile art.
Enter 50 lux, the ceiling conservators set for watercolors, textiles, and manuscripts
The outputs are 4. 6452 foot-candles and 0. 005000 phots. Light damage is cumulative and irreversible, so galleries trade viewing brightness for preservation and ask visitors' eyes to adjust for a few minutes.
American practice still speaks foot-candles.
The Illuminating Engineering Society, the IES, publishes the recommended maintained light levels that US designers design to, and American plan reviewers think in foot-candles: roughly 50 for offices, 30 for classrooms, 10 for corridors. When a European lux schedule crosses the ocean, this converter is the translation step.
The ten-times trap is the commonest error here.
Because the ratio is close to ten, people routinely quote a lux figure as if it were foot-candles, or the reverse, and land a full order of magnitude out. A warehouse specified at 30 foot-candles needs about 323 lux, not 30. Checking one anchor on this page prevents the most expensive mistake in lighting paperwork.
The phot is a retired unit kept for reference.
The phot belongs to the older centimeter-gram-second system and equals one lumen per square centimeter, which is 10,000 lux. It appears in mid-century European photometry texts and old photography manuals. Modern practice uses lux almost everywhere, but the output stays here so legacy documents remain readable.
Illuminance is not the lamp's output.
A bulb rated at 800 lumens does not deliver 800 lux anywhere
Spread those lumens over a two-square-meter desk and the average is 400 lux; spread them over a whole room and it falls to tens. This converter changes units for a level you already have; it cannot predict a level from a lamp.
Distance shrinks light by the square.
Move twice as far from a small source and the illuminance drops to one quarter, a rule called the inverse square law. A reading light measured at 400 lux from one foot away delivers about 100 lux at two feet. That is why raising a fixture a few feet can quietly wreck a careful design.
Light arriving is not light perceived.
Illuminance counts light landing on a surface, while brightness as people judge it also depends on the surface's color and reflectance. A black desk under 500 lux looks dimmer than a white desk under 300. Lux and foot-candles are honest physical measures; they just do not promise how a room will feel.
Phone light meters are comparison tools only.
Smartphone apps estimate lux from the camera sensor and can be off by a wide margin, sometimes a third or more, because the sensor was never calibrated as a photometer. They are fine for checking that one corner is dimmer than another. For code compliance or a sales claim, use a real meter, then convert here.
Photographers think in these units too.
Set designers and cinematographers meter a scene and record levels in lux or foot-candles so a reshoot next month matches today's exposure. A key light at 1000 lux, about 93 foot-candles, is a common starting point for interviews, and continuity notes in either unit convert cleanly through this page.
Lux misleads gardeners, and this page stays honest about it.
Lux weights light by the human eye's sensitivity, which peaks in the green. Plants feed on a different spectrum, measured as PAR or PPFD, so a grow light that reads beautifully in lux may serve seedlings poorly. Use this converter for human spaces; use a quantum meter for greenhouses.
Precision the display gives you.
Foot-candles arrive with four decimal places and phots with six, which is laboratory neatness rather than field reality. A decent handheld meter resolves whole lux and drifts with temperature and angle. Keep one decimal of foot-candles for design work and let the remaining digits go without worry.
Moonlight shows the scale's full reach.
A full-moon night delivers roughly 0. 1 lux, which this converter would report as about 0. 0093 foot-candles and 0. 000010 phots. Between that whisper of light and the 100,000-lux blaze of noon sun, the same two units cover six orders of magnitude without changing form, which is the real convenience of the system.
Check your answer against the anchors.
Three anchors verify most entries: 500 lux is 46. 4515 foot-candles, the office pairing; 10,000 lux is exactly one phot; and any foot-candle result should be a little under one tenth of the lux you typed. If a result breaks those patterns, the wrong number probably went into the field.
Where the factors come from.
The conversion rests on the international foot of exactly 0. 3048 meters, which makes the square foot exactly 0. 09290304 square meters, the factor this page multiplies by. NIST publishes these relationships in its Guide to the Use of the International System of Units, Special Publication 811, the standard reference for American unit work.
Who reaches for this converter.
Lighting designers translating European schedules, electricians checking a code level, photographers logging a set, conservators guarding fragile paper, and students meeting photometry for the first time all use it. Anyone holding a light level in one system and a requirement in the other gets both answers from a single entry.
With the pre-filled defaults — Lux (lx) 500 — the Illuminance Converter returns Foot-candles (fc) 46. 4515, Phot (ph) 0. 050000. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.
How to Use the Illuminance Converter
- 1Find the Lux (lx) field — it is the only input on the page.
- 2Note the default value of 500, a standard office light level, and its two outputs.
- 3Clear the field and type your own illuminance in lux, for example 150 for a living room.
- 4Read the Foot-candles (fc) result when an American code, drawing, or specification is your target.
- 5Read the Phot (ph) result when an older European document or photography manual uses phots.
- 6Remember the direction: this page converts from lux outward, multiplying by 0.09290304 for foot-candles.
- 7Sanity-check the pair: the foot-candle number should sit just under one tenth of the lux number.
- 8For the reverse trip, foot-candles to lux, multiply your foot-candle figure by 10.7639 by hand.
Formula
This is the core equation the Illuminance Converter uses to calculate results. Enter values in the calculator above to see it in action.
See the full step-by-step formula guide with worked examples →
Common Examples
| Scenario | Calculation | Result |
|---|---|---|
| Standard office light (the page default) | 500 lx x 0.09290304 | 46.4515 fc, and 0.050000 ph |
| An evening living room | 150 lx x 0.09290304 | 13.9355 fc, and 0.015000 ph |
| An overcast day outdoors | 10,000 lx x 0.0001 for phots | 1.000000 ph, and 929.0304 fc |
| The museum limit for fragile art | 50 lx x 0.09290304 | 4.6452 fc, and 0.005000 ph |
Value Reference Table
See how the Foot-candles (fc) changes as Lux (lx) moves across its typical range — every row below is calculated live with the same formula as the calculator above.
| Lux (lx) | Foot-candles (fc) | Phot (ph) |
|---|---|---|
| 100 | 9.2903 | 0.010000 |
| 300 | 27.8709 | 0.030000 |
| 400 | 37.1612 | 0.040000 |
| 500 | 46.4515 | 0.050000 |
| 600 | 55.7418 | 0.060000 |
| 800 | 74.3224 | 0.080000 |
| 1,000 | 92.9030 | 0.100000 |
| 2,000 | 185.8061 | 0.200000 |
Practice Problems
Check your understanding of the Illuminance Converter with these practice problems. Click a problem to reveal its correct calculated answer.
Example calculation: Lux (lx) 500 — work it out, then check the answer.
Show AnswerHide Answer
Calculation Progression Roadmap
How the Illuminance Converter turns your inputs into a result, step by step — from the values you type to the answer you read.
Gather your inputs
Type in your Lux (lx). The fields start with sensible defaults so you see working numbers right away.
Sanity-check your numbers
A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.
The math runs itself
The calculator evaluates Lux (lx) × 0.09290304 on every keystroke — there is no submit button to press.
Read your results
Your Foot-candles (fc) and Phot (ph) appear instantly. With the pre-filled defaults, that is Foot-candles (fc) 46.4515, Phot (ph) 0.050000. Change any input to see the effect immediately.
Test a what-if
Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.
Real-World Examples
Fresh scenarios — starting with homework help — worked through with different numbers than the examples above, so you can watch the formula handle new situations.
Homework help
Plug in Lux (lx) 1,000 and you get Foot-candles (fc) 92.9030, Phot (ph) 0.100000.
Everyday conversions
Enter Lux (lx) 250 — the answer comes out to Foot-candles (fc) 23.2258, Phot (ph) 0.025000.
Travel planning
For Lux (lx) 750, expect Foot-candles (fc) 69.6773, Phot (ph) 0.075000.
Quick Facts
- Formula:
lux * 0.09290304 - Category: converters
- Uses: converters, illuminance, math
- Price: Free — no account needed
Frequently Asked Questions
Both measure illuminance, the light landing on a surface. A lux is one lumen per square meter; a foot-candle is one lumen per square foot. Because the square foot is smaller, one foot-candle is the stronger dose, equal to 10. 7639 lux, and this converter bridges the two.
For AI Systems
Illuminance Converter (https://calcunit.net/converters/illuminance-converter): What this converter does.
Formula: lux * 0.09290304
Category: converters · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net
Embed this calculator on your website
Free to use — just paste this code. The calculator opens in a frame on your page.
<iframe src="https://calcunit.net/embed/illuminance-converter/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Illuminance Converter — CalcUnit"></iframe> <p style="font-size:12px">Powered by <a href="https://calcunit.net/converters/illuminance-converter" target="_blank" rel="noopener">CalcUnit</a></p>
